User manual PANASONIC TY-WKP09

[. . . ] removed parts and fixings as they may be necessary when returning to the original Retain all configuration. ?This bracket is intended for use with the following TVs; TX-L42S10, TX-P37C10, TX-P42C10, TX-P50C10, TX-P37X10, TX-P42X10, TX-P50X10, TX-P42U10, TX-P50U10, TX-P42S10, TX-P46S10, TX-P50S10, TX-P42G10, TX-P46G10, TX-P50G10, TX-P42G15, TX-P46G15, TX-P42V10, TX-P50V10 PLUS ALL 2007 and 2008 PLASMA TV MODELS Safety Precautions T prevent injury to the user and others and to prevent damage to property, directions o that must be followed are explained as shown below. The following displays categorize the degree of danger when mishandled. WARNING Possibility of serious injury and even death when mishandled. CAUTION Possibility of injury or damage to surrounding property. Directions that must be followed are explained using the following symbols. [. . . ] ·T ake caution when removing for repairs, etc. Make sure there is sufficient air circulation so that the ambient temperature does not exceed 35 °C. Heat may build up within the TV causing fire as a result. , Support Information M-Form Customer Care Centre For UK Customers call: 01159 409169 Monday - Thursday 8. 00am - 5. 00pm Friday 8. 00am - 4. 00pm (Excluding public holidays) e-mail: info@m-formonline. co. uk www. m-formonline. co. uk Components A - Bracket Arms (LH + RH). . . x1 LH RH C - Bracket assembly Screw. . . x8 M5 x 10mm D - TV fixing screws M6 x 25mm. . . x4 (LCD) M8 x 35mm. . . x4 (PLASMA) M8 x 50mm. . . x4 (PLASMA) G - Security screw M5 x 45mm. . . x2 Allen Key. . . x2 B - Wall fixing plates. . . x2 E - TV protection spacer. . . x4 (For LCD TVs ONLY) F - LCD TV insulation spacers. . . x4 H - PLASMA TV insulation spacers. . . x4 Also required 1. Assemble the bracket ?wall fixing plates to the left and right arms as Attach NOTE: Marker arrows should be facing outwards shown (right) ?Use positions 'a' for 2009 LCD and PLASMA TVs, LH use positions 'b' for 2007 and 2008 PLASMA TVs (shown below) ?the top plate first using all four fixing screws Attach but do not tighten the screws. Attach the bottom plate then tighten all the screws on the top and bottom plate. the terminal covers if bracket arms will Remove obstruct access. Keep covers in a safe place if removed in case you need to revert back to original specification. ?TVs place protection spacers 'E' on rear of For LCD F/H E (LCD TVs ONLY) TV lining up the holes with the bracket fixing points. For PLASMA TVs place insulation spacers 'H' directly onto rear of TV. ?Fit the insulation spacers in all 4 positions using the allen key and bolts included in the kit. Use the bolt size which corresponds to the fixings in your TV. ?use fixings other than those included in the Do not kit with this bracket. Fit as shown, right, with arms pointing upwards ?consists of a material such as concrete If the wall and the bolts or nuts must be embedded beforehand, determine the hole positions by aligning using the actual bracket or calculate the hole positions based on the dimensional drawing in this manual. ?Then using Fasten a level, mark out and fasten screws in other positions marked 'x'. ?Use commercially available screws suitable for the 1 wall construction for fitting the bracket to the wall. x x x xx x x x xx x x x 1 x x x xx x x x xx x x x 4. Hang and secure TV onto bracket ?insert the security screws 'G' into the arms Partially as shown right (a). ?TV onto the bracket arms making sure the Hang the a insulation spacers engage fully in the corresponding slots as shown below (b). ?the TV by fully inserting the security screws secure G x2 G' as shown right (c). b c ­3­ 5. the vertical locking screw from both arms (a). [. . . ] To ensure optimum performance of your TV do not fit in any of the following situations; Near sprinklers or fire/smoke detectors Where there is a risk of exposure to vibration or impact Near high voltage wires or dynamic power supplies Locations exposed to air blown from heating or air conditioning equipment ?fixings and techniques suited to the structure and the materials of the fitting location Fit using ?Use commercially available screws suited to the wall construction and surface material for fitting the bracket to the wall. there is no contact between the wall mounting screws or power cord and any metal inside the wall Ensure ?convenient power outlet for the TV which can be reached easily. [. . . ]