User manual PANASONIC U-6LE1E8

[. . . ] Do not install the air conditioner where excessively high heat-generating objects are placed. Avoid: To protect the air conditioner from heavy corrosion, avoid installing the outdoor unit where salty sea water can splash directly onto it or in sulphurous air near a spa. Electrical Requirements 1. All wiring must conform to the local electrical codes. Consult your dealer or a qualified electrician for details. Each unit must be properly grounded with a ground (or earth) wire or through the supply wiring. [. . . ] The unit automatically recovers after a few minutes. The English text is the original instructions. Other languages are translation of the original instructions. • • • • • • • • • • • • • • • • • • • • NOTICE • • 4 OI-141-4-EN 01_85464609141021_EN. fm Page 5 Thursday, August 11, 2011 11:24 AM Wireless Remote Controller (Optional parts) NOTE Refer to the Operating Instructions attached to the optional Wireless Remote Controller. Timer Remote Controller (Optional parts) NOTE Refer to the Operating Instructions attached to the optional Timer Remote Controller. Operation Condition Use this air conditioner under the following temperature range. Indoor temperature range: Cooling mode 14°C ~ 25°C (*WBT) / 18°C ~ 32°C (*DBT) Heating mode 16°C ~ 30°C (*DBT) Outdoor temperature range: Cooling mode -10°C ~ 46°C (*DBT) Heating mode -20°C ~ 18°C (*WBT) / -20°C ~ 24°C (*DBT) *DBT: Dry bulb temperature *WBT: Wet bulb temperature OI-141-5-EN 5 01_85464609141021_EN. fm Page 6 Thursday, August 11, 2011 11:24 AM Adjusting the Airflow Direction The functions differ depending on the indoor unit used. The airflow direction cannot be set using the remote controller for any unit which is not listed below. U1 type, Y1 type, L1 type, D1 type, T1 type and K1 type. • • • Never use your hands to move the flap (vertical airflow flap) that is controlled using the remote controller. When the air conditioner is turned off, the flap (vertical airflow flap) automatically moves to the downward position. The flap (vertical airflow flap) moves to the upward position when performing the standby operation for heating. The swing operation is made after the standby operation for heating is released, but swing is indicated on the remote controller even during the standby operation for heating. FLAP button is pressed during operation. Setting the airflow direction To activate the swing operation The airflow direction changes each time the Press the FLAP button to set the flap (vertical airflow flap) to the downward position, and then press the FLAP button again. This displays , and the airflow automatically swings up and down. Cooling and drying The flap (vertical airflow flap) can be set to one of three positions. Heating Set the flap (vertical airflow flap) to the downward position. When operating continuously in the fixed airflow direction setting for about an hour, the airflow direction is automatically controlled and the flap position is changed. The airflow direction may be different from the display on the remote controller. Zone ‘‘A’’ for cooling Zone ‘‘B’’ for heating Indoor unit Horizontal directions (manual) The horizontal airflow direction can be adjusted manually by moving the vertical vanes to the left or right. Concealed duct type (F1, M1, E1) This air conditioner is not equipped with air outlet parts. Please refer to the manual of the locally adopted air outlet parts. OI-141-7-EN 7 01_85464609141021_EN. fm Page 8 Thursday, August 11, 2011 11:24 AM Adjusting the Airflow Direction for Multiple Indoor Units Using a Single Remote Controller (Wired) • • Auto Flap ( ) button • The airflow direction cannot be set using the remote controller for the concealed duct type (F1, M1, E1) and floor standing type (P1, R1). If multiple indoor units are connected to a remote controller, the airflow direction can be set for each indoor unit by selecting the indoor units (see the operation below). To set the airflow for individual units, press the UNIT button. Display shows the indoor unit number under group control. Set the airflow direction for the indoor unit that is shown on the display. [. . . ] [Information on Disposal in other Countries outside the European Union] These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Note for the battery symbol (bottom two symbol examples): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. Pb Safety Instructions To be followed absolutely Stop using the product when any abnormality/failure occurs and disconnect the power plug. [. . . ]