User manual PARADOX DGP-848

[. . . ] Digiplex 48-Zone Control Panel (DGP-848) Programming Guide Software Version 4. 13 Includes DGP-641BL/RB Programming Guide DGP-848 Default Installer Code 000000 (see section [800] on page 39) Default System Master code 123456 How Do I Enter Programming Mode? 1. Enter required [DATA]. Decimal and Hexadecimal Programming Table Certain sections may require the entry of one or more Hexadecimal values from 0 to F. For LCD keypads: [0] to [9] [STAY] [FORCE] [ARM] [ENTER] = values 0 to 9 respectively =A =B =C = Save current data and advance to next section [DISARM] [BYP] [MEM] [CLEAR] =D =E =F = Exit section without saving For Grafica keypads: [#] [0] to [9] = values 0 to 9 respectively = A to F (press the [#] key until the desired letter appears) Right Action Key (Exit) = Exit section without saving Center Action Key (Save) =Save current data and advance to next section DGP-848 -1- Programming Guide Table of Contents Serial Number List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Zone Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Keyswitch Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Module Reset: Reset a module's programmed contents to default by entering its serial number. Locate/Unlocate Module: Locate a specific module (e. g. detector, zone expander, etc. ) connected to the combus by entering the module's serial number. The green "LOCATE" LED on the module will begin to flash until the serial number is reentered or the appropriate "tamper" or "unlocate" switch on the module is pressed. Module Programming Mode: Enter the serial number of the module you wish to program. Module Broadcast: Copy the contents of all programming sections from one module to one or more modules of the same type. Enter the serial number of the source module, followed by the serial numbers of the modules you wish to program. To begin transferring data, press [ACC] on LCD keypads or the center action key (Start) on Grafica keypads. PLEASE NOTE: The Module Broadcast feature will only work when a module is broadcasting its data to a module or to modules of the same type and model number. For example, an APR-PRT1 (Printer Module) cannot broadcast to an APR3-PRT1. Likewise, a DGP module cannot broadcast to a DGP2 module. [950] [951] [952] [953] [954] [955] Remove Modules: After entering the section, the control panel will scan all modules connected to the combus. If any missing modules are detected (i. e. detector removed from the combus), the control panel will erase the module's serial number, removing the module from the control panel's memory. Paradox Memory Key [961] [962] [965] [966] Download from the Memory Key to control panel except sections [001] to [056]. Download from the Memory Key to control panel including sections [001] to [056]. Copy the control panel sections to the Memory Key except sections [001] to [056]. Copy the control panel sections to the Memory Key including sections [001] to [056]. Download Memory Key to Control Panel 1. Remove AC and battery power from the control panel you want to program. Insert the Memory Key onto the control panel's connector labelled "DIGIPLEX KEY". To download the contents of the Memory Key except sections [001] to [048] (device serial numbers) and [049] to [056] (Keyswitch serial numbers), enter installer programming mode, then enter section [961]. To download the contents of the Memory Key including sections [001] to [048] and [049] to [056], enter installer programming mode, then enter section [962]. When the keypad emits a confirmation beep, wait 10 seconds and remove the Memory Key. Remove AC and battery power from the control panel you want to copy. [. . . ] Seller obligation and liability under this warranty is expressly limited to repairing or replacing, at Seller's option, any product not meeting the specifications. Returns must include proof of purchase and be within the warranty period. In no event shall the Seller be liable to the buyer or any other person for any loss or damages whether direct or indirect or consequential or incidental, including without limitation, any damages for lost profits stolen goods, or claims by any other party, caused by defective goods or otherwise arising from the improper, incorrect or otherwise faulty installation or use of the merchandise sold. Notwithstanding the preceding paragraph, the Seller's maximum liability will be strictly limited to the purchase price of the defective product. [. . . ]