User manual PARKSIDE BJ 2002

[. . . ] Be careful to retain these operating instructions and safety advice notes and if necessary pass them on to a third party. OPERATING INSTRUCTIONS To obtain the best results do not use too much pressure but try to work using a constant speed. The following basic rules apply: small tools = high speed and large tools = low speed. For milling and engraving work, hold the tool like a pen (keeping the ventilation slots free). [. . . ] Use these attachments particularly for miscellaneous types of work such as recessing, carving, shaping, grooving or chasing (see Fig. i). Material Hardwood Softwood Plastic Steel Aluminium etc. ­ low low ­ medium low ­ medium Controller setting Speed ranges:: 5 POLISHING Attachments: Areas of use: Figure k): 3 polishing pads The polishing pads can be used for most metals and plastics (see Fig. They are particularly suitable for precious metals like gold or silver. When polishing you must always use very light pressure only. Material Steel Aluminium and precious metals Speed min. ­ low Controller setting Speed ranges: DRILLING Attachments: Areas of use: Speed ranges: Figure m): 6 universal HSS drills The drills, sized 0. 8, 1. 0, 1. 2, 1. 4, 1. 6, 1. 8, are suitable for metal and plastic (see Fig. n). Material Hardwood Softwood Plastic Steel Aluminium etc. ­ low low high Controller setting CHUCKS Chucks: Areas of use: Figure o): 2 attachment clamps with threaded connection , 4 collet chucks diameters, some also fit the special tools in various The range of chucks and clamps ensures that the special attachments can always be fitted as required. They guarantee that the tool is securely held and that you will obtain the best results. Attachment clamp with threaded connection for: Saw blade , cutting disc , Silicon grinding disc (green) , corundum grinding disc (red) , polishing pads 2. 3 mm collet chuck (standard collet chuck) for: , "diamond bits" silicon grinding point (green) , corundum grinding point (red) , 1 plastic brush , 1 plastic brushing disc , brass brushing disc , milling bits , HSS drills 1. 2, 1. 4, 1. 6, 1. 8 (for 0. 8 and 1. 0 drills please use the corresponding size of collet chuck). 6 INSERTING / CHANGING CHUCKS WARNING: Pull out the mains plug before changing attachments. Never engage the spindle lock ² (Fig. p) and press the spindle lock ² until it engages. Unscrew the chuck ¶ and replace it with another chuck or clamp. INSERTING TOOL / ATTACHMENTS IN CHUCK WARNING: Pull out the mains plug before changing any attachments. Never engage the spindle lock ² (Fig. p) and press the spindle lock ² until it engages. Slacken the chuck ¶ and change the attachment. [. . . ] We reserve the right to make technical modifications in the course of further development. STATEMENT OF CONFORMITY We, Kompernaß Handelsgesellschaft mbH, Burgstr. 21, D-44867 Bochum, Germany, hereby declare that this product conforms with the following EC regulations: EC machine guideline/ EC low voltage regulations: Electromagnetic compatibility: Applicable harmonised standards: 73/23 EEC, 93/68 EEC (Low Voltage Directive) 89/336 EEC (EMC Directive) EN 55014-1:2000, EN 55014-2:1997 EN 61000-3-2:2000, EN 61000-3-3:1995 EN 61558-1:1997+1998 EN 61558-2-6:1997 KL-C102 POWER ADAPTOR Model type: Description: Bochum, 30. 06. 2002 Hans Kompernaß - Managing Director - 7 WARRANTY This piece of equipment is covered by a 36-month warranty as of the date of purchase. The equipment was produced with the greatest of care and underwent thorough testing before delivery. [. . . ]