User manual PARKSIDE PDS 150 BENCH GRINDER

[. . . ] This does not affect your legal rights. IMPORTANT SAFETY ADVICE Ensure that you observe the following safety instructions specifically for this equipment and in addition that you read the advice in the accompanying booklet called "Safety advice" before using the equipment for the first time. Not following the safety instructions and advice can lead to accidents, electric shock, injuries, risks to health, or burns. 4 This bench grinder is intended to be used exclusively for dry grinding. Materials dangerous to health, such as asbestos are not to be abraded. Look after your health ­ please wear safety glasses and a breathing /dust mask. [. . . ] Retighten the adjustment screw ² and check using your hand that the grinding wheel µ movement is true and free. If the grinding wheel µ is worn so much that the above clearance can no longer be achieved even after adjustment of the workpiece support ¿/¶ or the eye shield mount », then the grinding wheel must be changed. í COMMISSIONING Ensure that the equipment is switched off and that the ON/ OFF switch ´ is in the "0" position. The voltage must agree with that shown on the equipment rating plate (equipment shown as 230 V can also be connected to 220 V). ON / OFF switch ´ in position "1" = equipment runs at a constant speed ON / OFF switch ´ in position "0" = equipment is switched off í USE To grind metal tools or metal items, place the workpiece on the workpiece support ¿/¶ and slowly bring it close to the grinding wheel µ. Carefully press the workpiece against the grinding wheel µ. Too much pressure can lead to overloading of the bench grinder. Grinding should be carried out only on the circumference of the grinding wheels. 5 CHANGING A GRINDING WHEEL Always make sure that the mains plug is out of the socket before doing any work on the equipment and when it is out of use. You must only use grinding wheels on which the manufacturer's information, the type of adhesive, dimensions and permitted speed agree with the technical information specified for this bench grinder. Do not use any damaged or distorted grinding wheels. If you install new grinding wheels carryout a ringing test before use. Grinding wheels in good condition give a clear ringing noise when struck lightly with a plastic hammer. Take off the wheel guard cover º, eye shield · and the wheel edge cover ¾, and slacken the workpiece mount ¿/¶. You must ensure that the left-hand side of the bench grinder (see Fig. 2) has a left-hand thread and the right-hand side has a right-hand thread. The notched nut ¹ indicates the left-hand thread. The nut without notches corresponds to the right-hand thread. This ensures that the nuts can only be screwed off in the direction of rotation of the spindle. Now change the grinding wheels and reassemble all the components in the reverse order. WARNING ! 01. Do not interchange the flanges when attaching the grinding wheels (see Fig. 2). Use only the clamping flange supplied to mount the grinding wheels. [. . . ] This electrical equipment complies with the relevant safety regulations. Repairs may only be carried out by a specialist electrical repair centre using original spare parts, otherwise injury could occur to the user. You can find further practical tips on electrical tools in the accompanying booklet "Safety Advice". 6 STATEMENT OF CONFORMITY We, Kompernaß Handelsgesellschaft mbH, Burgstr. 21, D-44867 Bochum, Germany, hereby declare that this product conforms with the following EC regulations: EC machine guideline: EC low voltage regulations: Electromagnetic compatibility: Applicable harmonised standards: 98/37 EEC 73/23 EEC (with change EC directive 93/68 EEC) 89/336 EEC (with change EC directive 93/68 EEC) DIN VDE 0741/08. 63 DIN 66069/06. 73 VBG 7n/01. 93 EN 61029-1:2000 PrEN 61029-2-4:1992 EN 55014-1:1993/A2:1999 EN 61000-3-2/1995/A2:1998 EN 55014-2:1997 EN 61000-3-3:1995 Manufacturer: Model type: Description: PARKSIDE PDS 150 BENCH GRINDING MACHINE Bochum, 31. 07. 2002 Hans Kompernaß - Managing Director - 7 WARRANTY This piece of equipment is covered by a 36-month warranty as of the date of purchase. The equipment was produced with the greatest of care and underwent thorough testing before delivery. [. . . ]