User manual PARKSIDE PEH 950

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual PARKSIDE PEH 950. We hope that this PARKSIDE PEH 950 user guide will be useful to you.

Lastmanuals help download the user guide PARKSIDE PEH 950.


Mode d'emploi PARKSIDE PEH 950
Download
Manual abstract: user guide PARKSIDE PEH 950

Detailed instructions for use are in the User's Guide.

[. . . ] If the mains cable is damaged or cut through during the work - never touch the cable - pull out the mains plug immediately. Never use electrical equipment with damaged cables. For operating the planer for longer periods and particularly if dust that may be hazardous to heath is created, the planer should be connected to a suitable external vacuum device. Always keep the power cable fed to the rear of the machine. [. . . ] Always switch on the planer before making contact with the material and then guide the planer on to the workpiece. PLANING SURFACES Place the planer with the front of the base plate ¾ on the workpiece. Always make sure when you are planing surfaces such as beams and boards that the base plate ¾ is in full contact with the surface to avoid the danger of blade kickback. Always use both hands to guide the plane over the workpiece with even forward pressure. CHAMFERING CORNERS The vee groove ¸ in the centre of the front of the base plate ¾ allows you to chamfer the corners of your workpiece very quickly and easily. Place the planer on to the workpiece with the vee groove ¸ on the corner and then guide the planer along the corner. Make sure you keep the angle at 45° and an even forward pressure. REBATING Example set up: for right hand rebates the side fence ² goes on the left and the rebating depth stop ¶ goes on the right into the holes on the planer (with the planer viewed from above). WARNING: Before doing any work on the planer always pull out the plug from the mains. IMPORTANT ADVICE: Do not unscrew the two hexagonal socket headed screws. they adjust the height of the cutting block. Adjustment is only required if you wish to change to another planer blade type e. When you change blades, always change both blades to avoid any imbalance. When they become blunt, the PARKSIDE reversible blades can be changed without any height adjustment of the cutting block being necessary 1) First unscrew one cutting block ¹ only so that you can use the works-mounted second cutting block as an aid to setting up later. 2) Unscrew the three screws in the cutting block ¹ using the supplied open spanner. 5) Re-assembly with a reversed or new blade is done in reverse order. 6) Check again for safety: - the position of the planer blade in the cutting block - the balanced and secure seating of the cutting block and the 3 fixing screws - that the height adjustment is correct (2 hexagonal socket headed screws). 7) Planer blades can be obtained from the service address indicated (see guarantee). Unscrew the screws in the cover and take off the toothed belt cover ´. Cut through the toothed belt with side-cutting pliers or a knife and remove the severed toothed belt. Always clean off any dirt or debris from the pulley and the drive wheel before installing the new belt. Place the new toothed belt on to the drive wheel and push the belt over the large pulley wheel whilst turning it. [. . . ] FALSA Montera parallellanslag ² till vänster och falsdjupanslag ¶ till höger i borrhålen på hyveln (montering sett från ovan) för att få en högerliggande fals. This piece of equipment is covered by a 3-year warranty as of the date of purchase. The equipment was produced with the greatest of care and underwent thorough testing before delivery. In the unlikely event of detecting a functional defect, please return the equipment in its original packaging with the proof of purchase to the closest service address. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PARKSIDE PEH 950

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual PARKSIDE PEH 950 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag