User manual PARROT MKI9000

[. . . ] Parrot MKi9000 User guide 1 Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Checking the car configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The choice of the mute-in jack depends on your car stereos configuration. 3 Installing the kit Note : If you have the possibility to use a multimeter, test and verify all connections on the vehicle before connecting the Parrot MKi9200 wiring loom. Car stereo with ISO connectors 1. Connect the male connectors of the hands-free kit to the car stereo. Join the vehicles audio and power supply cables to the female connectors of the Parrot MKi9000. On the installation cable, connect the free yellow wire to one of the audio systems corresponding mute-in jacks if available (mute in 1, mute in 2 or mute in 3). Note : Mute in 1, mute in 2 and mute in 3 are only suggested mute locations. You first have to test and verify the mute on the vehicle. 4 Car stereo with line-in Use this type of connection by wiring the line-out (brown & white wire or red & black wire) to your car stereos line-in. Using the two pairs of line-out will enable you to take advantage of the music function in stereo over your vehicles speakers. On the installation cable, connect the free yellow wire to the corresponding audio systems mute-input if available (mute in 1, mute in 2 or mute in 3). Installing the electronic box Avoid installing the electronic box near heating or air-conditioning system, on a spot directly exposed to sunlight or behind metal walls. Make sure the electronic box stays fixed once it is installed and that it will not move while you are driving. Do not reinstall the car stereo forcibly. If you are short of space behind the car stereo to install the electronic box, consider installing it in the glove box. 5 Installing the kits power cable Refer to your car stereos wiring diagram. The red wire of the kits cable must correspond to the constant +12V supply, the orange wire to the ignition +12V and the black wire to ground. Check that the orange wire is not connected to the constant +12V supply, as you could run down the vehicles battery. Note : On some vehicles, there is no ignition +12V on the vehicle's connectors. You must therefore connect the orange power supply wire to the fuse box or another ignition power source. Installing the audio connectors Installing the music cable Connect the music cable to the electronic box and place the USB / iPod / Jack connectors into the glove box, the central console or the parcel tray depending on the configuration of your dashboard. Make sure that the cable is not pinched. Note : Use the provided protection cap to protect the connectors. Installing the music cable grommet system The music cable grommet system allows you to adjust the cable length while reducing its wear. Drill a 20 mm hole in your dashboard (glove compartment or parcel tray). Insert manually two flexible arms of the grommet system. Use a flat screwdriver in order to insert the last two arms. > You can now connect your music cable to the bluebox. 6 Installing the individual components Installing the double microphone Selecting a location In order to get hi-quality conversations, we advise you to respect the following recommendations: Make sure the microphone is installed as close to the mouth of the user as possible. The best possible location for the microphone is near the rear-view mirror. The microphone needs to be pointed towards the user. D < 60 cm < 45° Make sure the microphone is not exposed to the air stream from air vents. Do not install the microphone cable in heating, ventilation or air conditioning systems. Mounting the The mounting location for the microphone must be clean and free from grease 7 double microphone or dust. Prior to installation, clean the area with an appropriate cleansing product. [. . . ] Use the jog wheel to select your DTMF between the following possibilities : 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, # or *. Press the jog wheel to send this DTMF to your phone. Ending a call Press the button to end a call. 16 Using voice recognition Receiving a call via voice recognition To receive a call via voice recognition, magic words must be activated. Activating / deactivating the magic words Note : Magic words are activated by default. 1. Press the jog wheel and select Phone > Voice Commands > Magic words. Press the jog wheel to activate/deactivate the magic words. Accepting a call Say « Accept » to answer an incoming call. Declining a call Say « Reject » to decline an incoming call. Making a call via voice recognition Calling a contact with one phone number 1. [. . . ]