User manual PARTNER P 461 II P.U.O.

[. . . ] Operator's Manual Manuale d'istruzioni Manuel d'instructions Bedienungsanleitung Manual de instrucciones Gebruikershandleiding Ägarhandbok Brugehåndbog Omistajankäsikirja Eierens Håndbok Manual de Instruções OHIE XPHE Használati útmutató READ CAREFULLY LEGGERE ATTENTAMENTE LIRE ATTENTIVEMENT SORGFÄLTIG LESEN LEER ATENTAMENTE EERST GOED DOORLEZEN LÄS NOGA LÆS OMHYGGELIGT LUE HUOLELLISESTI LES NØYE LER ATENTAMENTE IABATE POEKTIKA FIGYELEMMEL OLVASANDÓ g i i f C e h s q v { p k A. B. C. D. Partner oil 50 : 1 McCulloch oil 40 : 1 2T oil 25 : 1 1 ltr. 4 5 10 20 2% 20 cm3 80 100 200 400 2, 5% 25 cm3 100 125 250 500 4% 40 cm3 160 200 400 800 E. F. G. H. I. L. g Due to a constant product improvement programme, the factory reserves the right to modify technical details mentioned in this manual without prior notice. i La casa produttrice si riserva la possibilità di variare caratteristiche e dati del presente manuale in qualunque momento e senza preavviso. f La Maison se réserve la possibilité de changer des caractéristiques et des données de ce manuel à n'importe quel moment et sans préavis. [. . . ] CUTTING FALLEN TRUNKS 4 A) Limbing thick branches. For limbing and bucking leave the lower limbs to support the log off the ground. Begin with a bottom cut made by the upper side of the bar (A); the depth of the cut should be about one third of the log diameter. Finnish with a top cut (B) meeting the first one. With this technique splitting, cracking can be avoided C) Supported at both ends. Begin with a top cut about one third of the log diameter. Then finish with a bottom cut (B) meeting the first one. this technique avoids the risk of pinching the bar in the log. D) If the log is supported along its whole length it may be cut normally from above. Take care not to touch the ground with the chain. · When working on a slope always stand on the uphill. · When cutting prepared timber, use clamps or chocks to secure work. · Use extreme caution when cutting small size brush and saplings which may catch the chain and pull you off balance. 3 STARTING AND STOPPING E IMPORTANT Never start or operate unless bar and chain are properly installed. Before starting always move the saw away from the fuelling area and place it on a firm, flat surface, the guide bar to the front. STARTING A COLD ENGINE 1 Check that the chain brake is in the disengaged position moving the lever (L) towards the front handle. 2 Slide the choke lever (A) to the CLOSED position (OUT). Push the decompression valve (D) down if your models is fitted with one. 3 Depress throttle trigger lock out (S). Depress throttle trigger (G) and then operate throttle advance (P) moving it backwards. 4 Hold the saw firmly as shown in illustration and pull the starter rope until the engine fires once. 5 Move choke lever (A) to the OPEN position (IN). [. . . ] Tämä tyyppitesti vahvisti, että kone mukautuu EY koneohjeellisen välttämättömiin terveys-ja turvallisuusmääräyksììn. I følge EU Maskindirektiv (98/37/CEE), 93/68/CEE (CE-merkingsdirektiv) & 89/336/CEE (Direktiv om elektromagnetisk kompatibilitet) Direktiv 2000/14/CEE (Annex V). Undertegnede Fausto Parazzini, autorisert av E. O. P. I. , erklærer at bensindrevne kjedesager: MS38E, MS40E, MS46E med serienummer som vist oventor, med et kjedesverd med skjærelengde 35/40/45 cm, produsert av E. O. P. I. , Via Como 72, 23868 Valmadrera (LC), Italia, er i samsvar med den maskinen som var gjenstand for EU typeprøvning i følge Vedlegg VI til Maskindirektivet. EU typeundersøkelsen ble utført av Marchio di Qualità (IMQ), Via Quintiliano 43, 20138 Milano (Italia), EU Typeundersøkelsessertifikat nr. IMQ AQ 024DM, IMQ AQ 025DM, IMQ AQ 026DM. Denne typeprøvningen fastslo at maskinen tilfredstiller de nødvendige helse- og sikkerhetskravene i EU Maskindirektiv. [. . . ]