User manual PEAVEY ADDVERB II

[. . . ] Congratulations on your purchase of the XRTM 800F powered mixer. Peavey has packed features from the popular XR 684 into a professional 9-channel, tabletop package. The newest member of the famous Peavey XR family, the ADDVERB II, represents years of powered mixer experience combined with the latest in technology and packaging. Here are several features you will find on the ADDVERB II. [. . . ] The level of this signal is determined by the Right Master Fader. MONITOR OUTPUT: This 1/4" jack provides an output from the monitor mix to supply external power amp/monitor combinations. The level of this signal is determined by the Monitor Master Fader. ) This signal can be used with external effects units or as an additional (post fader) monitor output. The MASTER FUNCTIONS section describes those features that are considered master controls. Essentially, this makes up all of the functions on the right-hand, front panel side of your ADDVERB II. EFFECTS PEAK LED: Illuminates to indicate -6 dB of headroom before the signals being sent to the effects circuit are clipped. Ideally, you would want this LED to light only occasionally if at all. an occasional blink indicates that you have the levels at an optimum setting. It is advisable to listen carefully to the output at the same time in order to determine the final setting. If you hear distortion then one or more of the input digital effects level controls are set too high. MIC INPUT: XLR balanced, low impedance channel input optimized for a microphone or other low-level source. When the phantom power is enabled, this connector has +48 V on Pins 2 (in phase) and 3 with Pin 1 as the ground reference. The tip is the positive (in phase) input, which can also be used for unbalanced inputs. This signal is connected through a 20 dB pad to the mic input below it. Within the same channel, the Mic Input and the Line Input cannot be used simultaneously. Proper adjustment of the input gain will maximize the signal to noise ratio giving you the quietest operation. With your Channel Fader (35) set to the "0" position, set this control so that the Clip LED (34) barely lights at the highest peaks in your input signal. (The high control can also be found on Channels 7 through 9. This control sets the amount of cut or boost at the mid-frequency (850 Hz). The mid control can also be found on Channels 7 and 8. (The low control can also be found on Channels 7 through 9. [. . . ] Gain: Mic Input Adjustment Range: Mic Input to L and R Output Mic Input longest path Mic Input Adjustment Range: Line Input to L and R Output Mic Input longest path 10 dB to 48 dB 68 dB (Max Gain) 96 dB (Max Gain) power amp out -10 dB to 28 dB 49 dB (Max Gain) 77 dB (Max Gain) power amp out 01% 20 Hz -- 20 kHz line input to L/R output at output at nominal level (20 Hz -- 80 kHz BW) < . All faders down Master fader nominal, channel faders down All controls nominal, mic gain minimum All controls down Master fader nominal, channel sends down Master Fader Nominal, Channel Send Nominal All channel sends down All channel sends nominal (Hum and noise measurements: 22 Hz to 22 kHz BW) S/N Ratio: > 85 dB below rated output (200 W/channel), mic/line to speaker output Equivalent Input Noise (EIN): -128. POWER SECTION (400 SC Module with DDTTM) Power and Load: 210 W RMS per channel into 4 ohms 150 W RMS per channel into 8 ohms 420 W RMS Bridge into 8 ohms Frequency Response: 20 Hz--20 kHz +0 dB/-1 dB Total Harmonic Distortion: <0. Hum and Noise: -100 dB below 210 watts Damping Factor: Greater than 100 @ 1 kHz, 4 ohms Input Impedance: 2 k ohms Power Requirements: Dom. [. . . ]