User manual PEAVEY AUDITION 30

[. . . ] POWER LED (11) Illuminates when AC power is being supplied to the amp. pOWER SWITCH (12) Depress the switch to the "on" position. The red LED will illuminate indicating that power is being supplied to the unit. POWER AMP Rated Power 81 Load: 25 W RMS into 8 ohms Power @ Clipping: (typically) (5% THD, 1 kHz, 120 V AC line) 25 W RMS into 8 ohms Total Harmonic Distortion: Less than 0. [. . . ] The following specs are measured @ 2 kHz with the controls preset as follows: Channel Select Normal (out) Low& High @ 10 Mid @ 0 Pre Gain 6: Post Gain @ 10 Reverb 63 0 Nominal Levels are with Normal Gain @ 5 Minimum Levels are with Normal Gain @ 10 System Hum & Noise @ Nominal Input Level: (20 Hz to 20 kHz unweighted) 62 dB below rated power Equalization: Special low, mid, & high passive type EQ Due to our efforts for constant improvements, and specijicatiom listed herein are subject to change without PEAVEY ONE-YEAR LIMITED WARRANTY/REMEDY PEAVEY ELECTRONICS CORPORATION ("PEAVEY") warrants this product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from defects in material and workmanship for a period of one (1) year from date of purchase, PROVIDED, however, that this limited warranty is extended only to the origrnal retail purchaser and is subject to the conditions, exclusrons, and limitations hereinafter set forth: PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS If this product contains tubes or meters, Peavey warrants the tubes or meters contarned in the product to be free from defects in material and workmanshrp for a period of ninety (90) days from date of purchase; PROVIDED, however, that thus limited warranty is extended only to the original retail purchaser and IS also subject to the conditions, exclusions, and limitations hereinafter set forth. cONDITIONS , EXCLUSIONS , AND LIMITATIONS OF LIMITED WARRANTIES These limited warranties shall be void and of no effect , if: a. The first purchase of the product is for the purpose of resale: or b. The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER; or c. The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance, or other causes not arislng out of defects in material or workmanship; or d. the serial number affixed to the product is altered , defaced , or removed. In the event of a defect in material and/or workmanshrp covered by this limited warranty, Peavey will: a. , cases involving anything other than covers, footswitches, patchcords, tubes or meters), repair the defect in material or workmanshrp or replace the product, at Peavey's option; and provided, however, that, In any case, all costs of shipping, if necessary, are paid by you, the purchaser. tHE WARRANTY REGISTRATION CARD SHOULD BE ACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN (14) DAYS FROM THE DATE OF YOUR PURCHASE. In order to obtain service under these warranties, you must: a. Brina the defective item to anv PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL PRCOF OF PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER In connection with your purchase from him of this product. This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord. Never break off the ground pin on the power supply cord. For more information on grounding, write for our free booklet `Shock 9. Power supply cords should always be handled carefully. Never walk or place equipment on power supply cords. Periodically check cords for cuts or signs of stress, especially at the plug and the point where the cord exits the unit. The power supply cord should be unplugged when the unit is to be unused for long periods of time. If this product is to be mounted in an equipment rack, rear support should be provided. Metal parts can be cleaned with a damp rag. The vinyl covering used on some units can be cleaned with a damp rag or an ammoniabased household cleaner if necessary. [. . . ] Metal parts can be cleaned with a damp rag. The vinyl covering used on some units can be cleaned with a damp rag or an ammoniabased household cleaner if necessary. Disconnect unit from power supply before cleaning. Care should be taken so that objects do not fall and liquids are not spilled into the unit through the ventilation holes or any other openings. [. . . ]