User manual PEAVEY AXCELERATOR

[. . . ] OUTPUT SWITCH (4) Allows selection of power amp output to be selected from full power (120 watts) to half power (60 watts output). POWER LED (5) Illuminates when AC power is being supplied to the amp. STATUS LED (6) Illuminates when amp is switched to "Standby" indicating amplifier is not operational. mASTER VOLUME (7) Controls the overall volume level of the system. [. . . ] There may be some situations when audible hum and/or noise will come from the loudspeaker. If this occurs, position the Ground Switch to either positive or negative (+ or - ), or until the noise is minimized. Note: Should the noise problem continue, consult your Authorized Peavey dealer, the Peavey factory, or a qualified service technician. the Ground Switch is not functional on 220/240 volt models. LINE CORD-120 V products only (31) For your safety, we have incorporated a 3-wire line (mains) cable with proper grounding facilities. It is not advisable to remove the ground pin under any circumstances. If it is necessary to use the equipment without proper grounding facilities, suitable grounding adaptors should be used. Less noise and greatly reduced shock hazard exists when the unit is operated with properly grounded receptacles. POWER AMPLIFIER SECTION Four 6L6GCs with 12AX7 driver Rated Power & Load: 120 W RMS into 16, 8, or 4 ohms Power @ Clipping: (typically @ 5% THD, 1 kHz, 120 VAC line) 130 W RMS into 16, 8, or 4 ohms (Bias must be reduced to measure) Frequency Response: +0, -2 dB 50 Hz to 20 kHz @ 100 W RMS into 8 ohms Hum 81 Noise: Greater than 76 dB below rated power Power Consumption: Domestic: 400 W, 50/60 Hz, 120 V AC Export: 400 W, 60 Hz, 220-230/240 V AC Dimensions & Weight: 11 . The following specs are measured @ 1 kHz with the controls preset as follows: Low & High EQ @ 10, Mid EQ @ 0 Bright out Ultra & Crunch Posts @ IO Gain switches out Bottom, Body, & Edge @ 0 dB Reverb level @ 0 Master level @ 10 (Nominal levels are with Pre Gain @ 5. O mV RMS Preamp Low Gain Input: (-6 dB Pad) Impedance: High-Z, 44 K ohms (all levels are increased by +6 dB) Effects Send: Load Impedance: 47 K ohms or greater Nominal Output: -10 dBV, 300 mV RMS Effects Return: Impedance: Very High-Z, 470 K ohms Designed Level: -10 dBV, 300 mV RMS Preamp Output: Load Impedance: 47 K ohms or greater Nominal Output: +I0 dBV, 3 V RMS Remote Footswitch: Special 3-button unit with LED indicators (supplied) System Hum & Noise @ Nominal Level: (Clean channel - 20 Hz to 20 kHz unweighted) Greater than 74 dB below rated power (Special noise gate circuitry for Ultra & Crunch) Equalization: (clean channel on/y) Custom Low, Mid, & High passive type EQ Push Bright: +6 dB @ 2 kHz Voicing: (U/tra & Crunch channels only) Active Bottom, Body, & Edge EQ Push Gain: Increases gain in Ultra & Crunch channels Tone settings given are general and will vary according to the type of guitar, gauge type of the strings, the type of pickup, and even the type of pick. Your remedies for breach of these warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warranty only with respect to equipment purchased in the United States of America. In the event warranty service is required during the warranty period, you will need this document. There WIII be no identification card issued by Peavey Electronics Corporation. Completion and mailing of WARRANTY REGISTRATION CARDS - Should notification become necessary for any condition that may require correctlon, the REGISTRATION CARD will help ensure that you are contacted and properly notified. Notice of address changes - If you move from the address shown on the WARRANTY REGISTRATION CARD, you should notify Peavey of the change of address so as to facilitate your receipt of any bulletins or other forms of notification which may become necessary in connection with any condition that may require dissemination of information or correction. WARNING: When using electric products, basic cautions should always be followed, including the following: Read all safety and operating instructions before using this product. All safety and operating instructions should be retained for future reference. This product should not be used near water, i. This product should be located so that its position does not interfere with its proper ventilation. It should not be placed flat against a 6. This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier. [. . . ] This unit should be checked by a qualified service technician if: a. Anything has fallen or been spilled into the unit. The unit has been dropped or the enclosure damaged. The user should not attempt to service this equipment. [. . . ]