User manual PEAVEY BANDIT 75

[. . . ] 3 V RMS) when "out" and 0 dBV (1 V RMS) when "in. " RESONANCE SWITCH (16) Used to fine-tune the low frequency range of the speaker enclosure by varying the damping factor of the amplifier between two presets. pRESENCE (17) An active tone control that boosts the extreme high frequencies by 6 dB. T TM DYNAMICS CONTROL (18) Adjusts the power level of the amplifier from 10 percent to 100 percent power. [. . . ] Less noise and greatly reduced shock hazard exists when the unit is operated with properly grounded receptacles. When using remote footswitch, always insert the plug fully (second click) to insure proper operation. POWER AMP INPUT (25) Used to connect line level signal to the power amplifier. PREAMP OUT (26) The preamp out can be used to route the amplified signal to a mixing console, tape recorder, etc. connect the preamp output using a shielded cable to an input of the tape recorder , mixer , etc. This patch does not affect the operation of the amplifier. Dynamics @ IO 80 W RMS into 8 ohms 100 W RMS into 4 ohms Power @ Clipping: (typically) (5% THD, 1 kHz, 120 V AC line) 80 W RMS into 8 ohms 100 W RMS into 4 ohms Frequency Response: +O, 3 dB, 60 Hz to 20 kHz, @ 65 W RMS into 8 ohms Hum & Noise: Greater than 86 dB below rated power Power Consumption: 300 W @I 50/60 Hz, 120 V AC, Domestic 300 W @ 60 Hz, 220-230/240 V AC, Export PREAMP SECTION The following specs are measured @ 1 kHz with the controls preset as folio ws: Push Bright, Off (Out) Channel Select Normal (Out) Low & High @ IO Mid @ 0 Presence @ 0 dB Pre 5: Post Gain @ IO Gain 6: Thrash, Off (Out) Normal Levels are with normal volume @ 5 Minimum Levels are with normal volume @ 10 3 V RMS or 0 dBV, 1 V RMS if Effects Level is in (Switching jack provides Effects Send to Effects Return connection when not used) Preamp Output: Load Impedance: 1 K ohm or greater Nominal Output Level: 0 dBV, 1 V RMS Power Amp Input: Impedance: High-Z, 30 K ohms Designed Input Level: 0 dBV, 1 V RMS (Switching jack provides preamp output to power amp input connection when not used) System Hum & Noise @ Nominal Input Level: (20 Hz to 20 kHz unweighted) 72 dB below rated power Equalization: Special low, mid, & high passive type EQ Presence: +6 dB @ 5 kHz Push Bright: +6 dB @ 2 kHz Push Thrash: -20 dB notch @ 1 kHz in Lead channel Push Gain: Increases Lead gain Push Resonance: +6 dB @ cabinet resonance External Footswitch Functions: Lead Channel Defeat (when selected with button) Effects Loop Bypass Dimensions & Weight: 20. Due to our eflorts for constant improvements, ~features and specifications listed herein are subject to change without For further information on other Peavey products, ask your Authorized Peavey Dealer for the appropriate Peavey catalog/publication. PEAVEY ONE-YEAR LIMITED WARRANTY/REMEDY PEAVEY ELECTRONICS CORPORATION ("PEAVEY") warrants thus product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from defects in matenal and workmanship for a period of one (1) year from date of purchase, PROVIDED, however, that thus limited warranty is extended only to the origrnal retail purchaser and is subject to the conditions, exclusions, and limitations hereinafter set forth: PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS If this product contains tubes or meters, Peavey warrants the tubes or meters contained in the product to be free from defects in material and workmanshrp for a period of ninety (90) days from date of purchase; PROVIDED, however, that this limited warranty IS extended only to the original retail purchaser and IS also subject to the conditions, exclusions, and limitations hereinafter set forth. cONDITIONS , EXCLUSIONS , AND LIMITATIONS OF LIMITED WARRANTIES These limited warranties shall be void and of no effect , if: a. The first purchase of the product is for the purpose of resale; or b. Read all safety and operating instructions before using this product. All safety and operating instructions should be retained for future reference. This product should not be used near water, i. This product should be located so that its position does not interfere with its proper ventilation. It should not be placed flat against a 6. wall or placed in a built-in enclosure that will impede the flow of cooling air. This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord. Never break off the ground pin on the power supply cord. For more information on grounding, write for our free booklet "Shock 9. Power supply cords should always be handled carefully. [. . . ] This unit should be checked by a qualified service technician if: 15. Anything has fallen or been spilled into the unit. The unit has been dropped or the enclosure damaged. The user should not attempt to service this equipment. [. . . ]