User manual PEAVEY CD MIX 7032A

[. . . ] Bcf`oi-c using (Iii\ A A Estc \imbolo tiene el propci\ito dc ;Ilcrtx a l usuario de l a prcwncia clc `I(\ olt:I. je) pcIi~ro\o" clue no t i c n c aislaniiento dcntro tic l a caja dcl prod~icto qiie piicdt' tent3 una nla~nitud sut`icicntc coriio p;i~-a ~~rm4tituir I-ic4go dc corricnta70. Este simbolo ticnc el pIxq'ci\ito de alertar aI uwrio de la pwwncia de instrucconc~ importante~ \ob~-c Ia olw;IcitiIl y mantt'nimicnto cn l a littmtura cj~it' L icnc con ~1 producto. PRECACJCION: Ricsgo de corricntwo - No ah-a. P R E C A U C I O N : Pal-a di~minuir cl I-iesyo dc corrientwo. reparar. Deje todo mantcnimicnto ;I 10s t6cnicw calil`icado4. no ahra la cubierta. [. . . ] Right-hand ASSIGN switch set to channel #2 will access channel 2 when the crossfade slider is in the right-hand position. NOTE: It is useful to remember that when the crossfade slider is set to its center (number 5) position both channels assigned to the left- and right-hand crossfade positions will be at equal levels. You may then simply use the channel level controls to crossfade between the two assigned channels and ignore the crossfade, leaving it set in the center position. This is a more "European" technique of crossfading and is preferred by some DJs. (28) Crossfade slider: (29) 7-band EQ: Used to boost or cut seven selected frequency bands according to the placement of the seven slide potentiometers. (30) EQ in/out switch: When the switch is in the out position the 7-band EQ is bypassed. (31) Program loop in/out switch: When the switch is in the out position the program loop is bypassed. (32) Program Master level: A stereo slider that determines the overall program level from music channels 1, 2, 3, 4, and the microphone channel. (33) Mic-to-monitor on/off switch: When the switch is in the off position the microphones' signals are not fed through the monitor system. This is to enable in-booth program material to be played and cued without feedback from the booth microphones. When the switch is in the on position the microphones' signals are fed through the monitor system. In this way the monitor facility can be used to set the levels for a second music zone, e. g. a second dance floor or background level for another zone, instead of being used for monitoring in the DJ booth. (34) Monitor Master level: A stereo slider that determines the overall monitor level from channels 1, 2, 3, 4, and the microphone channel. (35) LED arrays (left and right): Two calibrated, LED arrays are provided to visually indicate program output levels. (36) Meter select switch: The cue position of this switch places the stereo LED array on the output of the cue system. The PGM position places the stereo LED array on the program output. (37) Power switch: Depress to the "On" position to turn the unit on. (38) Lamp: A 2-pin XLR jack is provided for connecting an optional gooseneck mixer lamp for illumination in adverse lighting conditions. Peavey accessory lamp number ML-3 is a suitable gooseneck mixer lamp for this purpose. 4 16VAC ' The second pair of monitor outputs may also be used to drive lighting controllers or for tape recording if required. Power input: (47) AC Input: External 16. 5 Volt, 1 amp power supply should be plugged in at this point. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord. Ne ver break off the ground pin on the power suPPlY cord. For more information on grounding, write for our free booklet "Shock Hazard and Grounding. " 10. Power supply cords should always be handled carefully. Never walk or place equipment on power suppl y cords. Periodically check cords for cuts or signs of stress, especially at the plug and the point where the cord exits the unit. The power supply cord should be unplugged when the unit is to be unused for long periods of time. If this product is to be mounted in an equipment rack, rear support should be provided. Metal parts can be cleaned with a damp rag. The vinyl covering used on some units can be cleaned with a damp rag or an ammoniabased household cleaner if necessary. Disconnect unit from power supply before cleaning. [. . . ] In the case of tubes or meters replace the defective component without charge b. In other covered cases (i. e. , cases involving anything other than covers, footswitches, patchcords, tubes or meters), repair the defect In material or workmanship or replace the product, at Peavey's option, and provrded, however, that, in any case, all costs of shrpping, if necessary, are paid by you, the purchaser. THE WARRANTY REGISTRATION CARD SHOULD BE ACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN (14) DAYS FROM THE DATE OF YOUR PURCHASE. In order to obtain service under these warranties, you must: a. [. . . ]