User manual PEAVEY CD MIX 9072A

[. . . ] CD MIXm 9072A Please read this entire manual before hooking the mixer into your audio system. CAUTION: Do not use spray cleaner for any slide control as this will wash out vital lubricants and shorten component life. A A #ithin the product'~ Intended to alert the ~iwr of the pl-esence 01` important operating a n d maintenance (wwicing) in\truc*tions in the liteI2tuI-e mxmpanyin~ the lmxluct. CAUTION: Risk of clcxtl-ical shock - DO NOT OPEN!C A U T I O N : To ~-cx~uce the I-isk of electric dmch, do not 1-e11wvt' COVCI-. No UWI- WI-\ iceablc part\ inside. Rcl. cr w-\/icing to qualified sewice pcIwnnc1. WARNIN appliance. thi4 appl iancc t o rain of nioi~tnrc. [. . . ] Then plug the power supply provided with your CD MIX 9072A into a main AC wall power receptacle. CAUTION: Use only the power supply that is provided with this product. If the original power supply must be replaced, consult your dealer or the factory for assistance in obtaining the correct replacement. Failure to use the correct power supply could result in fire or shock hazard, extensive circuit damage, decreased performance, or non-operation. +20dB I I I IIIIII I 1I I IIIIII I I ] +10dB OdB -lOdB -20dB 20 Hz 50 100 200 500 lk 2k Sk 10k 20k 40k EQ Frequency and Gain Characteristics 10 _ MIC LOOP IN LO POWER MID HI EOtJ%IZER MIC 1 RUT0 ON VOX POWER MIC 2 MONITOR MONITOR L OUTPUTS CROSSFADER MRSTER EP SELECT POWER AMP OUTPUTS BEAT METER SELECT . 9072A ·m~m~~em~~me~*om~mee* Professional DJ I Mixer CD MIXTM 9072A SPECIFICATIONS: SUMMARY OF FUNCTIONS: 7 Stereo inputs - 3 CD/phone and 4 line 4-way assignable crossfade 1 Microphone mixing bus with manual music over-ride switch, 3-band EQ, and automatic voice-over facility with on/off switch 1 O-segment LED ladders Switchable stereo headphone jack 15 V phantom power for electret mics 7-band program EQ &I2 dB 45 mm stereo crossfade slider One 12 VAC mixer lamp socket MICROPHONE AND CHANNEL 1 FUNCTIONS: Two low Z balanced microphone inputs with phantom power 3-band EQ Automatic voice-over switch Manual voice-over button Mic On/Off switch (Mic I) Mic/Line switch (Mic 2) 60 mm stereo level sliders Effects loop in/out switch Cue switch for Line input CHANNELS 2-4 FUNCTIONS (Each Channel): Stereo (RIAA) phono input switchable to CD Stereo line input CD/phone selector switch Stereo selector switch for line input or CD/phone input 60 mm stereo level slider Independent cue switch for each channel MASTER SECTION: 7-band graphic equalizer Stereo 1 O-segment LED display 60 mm stereo program level slider MONITOR SECTION: Mic On/Off switch 60 mm stereo monitor level slider CUE SECTION: Cue Headphone level Program Headphone level Cue/Program Headphone selector switch 12 CD/PHONO INPUTS: Phono position: Input Sensitivity: -50 dB (3 mV) Input Impedance: 47K ohms Max Input Level @ 1 kHz: -20 dBV (100 mV) CD position: Input Sensitivity: -10 dB (. 316 Volts) Input Impedance: 47K ohms Max Input Level: +I8 dBV (8 Volts) LINE INPUTS: Input Sensitivity: -10 dB (. 316 Volts) Input Impedance: 8. 3K ohms Max Input Level: +I8 dBV (8 Volts) MICROPHONE INPUTS (LOW-Z): Input Sensitivity: -70 dB (. 3 mV) Input Impedance: 3K ohms Max Input Level: +6 dBV (2 Volts) MICROPHONE TALKOVER: Attenuation (voice-over switch enabled or automatic voice-over enabled): 12dB FREQUENCY RESPONSE: Phono Inputs (RIAA): +O/-3 dB (20 Hz to 20 kHz) Line Inputs: +O/-3 dB (20 Hz to 20 kHz) Headphone: +O/-3 dB (40 Hz to 20 kHz) SIGNAL-TO-NOISE RATIOS: Phono: > 70 dB Line: > 90 dB DISTORTION: Less than . Ol% EQUALIZATION: 63 . +12dBat63Hz 160: *I2 dB at 160 Hz 400: &I2 dB at 400 Hz 1 K: +12dBatl kHz 2. 5K: +I 2 dB at 2. 5 kHz 6. 3K: +I 2 dB at 6. 3 kHz 16K: U2dBat 16 kHz MICROPHONE EQ: Low: +I5 dB at 50 Hz Mid: +I2 dB at 600 Hz . HI : +_15dBatlOkHz 13 MAX OUTPUT LEVEL: + 15. 5 dBV (6 Volts) POWER REQUIREMENTS: 16. 5 VAC, 1000 ma external power supply Installing the unit: This mixer may be mounted in a standard 19" equipment rack using 19" rackmounting screws and washers (Peavey accessory part #5003), or may be built into the surface of a DJ console by cutting a hole 16. 75" x 10. 5" and using screws to secure the unit. See diagram below for dimensions. -1 --I I t1 I I I . A mm - - - B - B - - - - - - ------s-v---m 4 -. lCUTOUT I I II 1 II SHADED 1 3. 75 IO 5" 1 I I PORTION I m m - - - - - s - - - - - - A-C, L------------ -1 ?I I 1I 1I I -----m I Q `JF;". s 7 ~~~~---~~~~ I I 46. 75"~`25!- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - C/L I 3. 75 I II I . tl -- ~~~~---I_----- L _c_c-m-----w--- -8, -v. I 1I I I -m 1- 1 device to each pair of outputs -7 Power Amp. lY(l L o u d s p e a k e r s . OR OR -1 Lighting controller Mono lines lrom mrre phones CHANNEL 4 CHANNEL 3 CHANNEL 2 CHANNEL 1 CD MIX 9072 A PATCH DIAGRAM ALL LINES ARE STEREO UNLESS NOTED 0 P IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following. Read all safety and operating instructions before using this product. All safety and operating instructions should be retained for future reference. Obey all cautions in the operating instructions and on the back of the unit. All operating instructions should be followed. This product should not be used near water, i. e. , a bathtub, sink, swimming pool, wet basement, etc. This product should be located so that its position does not interfere with its proper ventilation. It should not be placed flat against a 6. wall or placed in a built-in enclosure that will impede the flow of cooling air. This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord. [. . . ] Bring the defective item to any PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL PROOF OF PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product. If the DEALER or SERVICE CENTER IS unable to provrde the necessary warranty service you will be directed to the nearest other PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER which can provide such service. Ship the defective Item, prepaid, to: PEAVEY ELECTRONICS CORPORATION International Service Center 326 Hwy. 11 & 80 East MERIDIAN, MS 39301 Including therewith a complete, detailed description of the problem, together with a legible copy of the original PROOF OF PURCHASE and a complete return address. [. . . ]