User manual PEAVEY CLASSIC 400

[. . . ] fRONT PANEL FUNCTIONS INPUT PAD SWITCH (1) Provided for instruments that have extremely high output , which can result in overdriving (distorting) the input stage. Depressing the switch to its "in" position reduces the level of the input signal by 10 dB. INPUT JACK (2) This input will accept signals from all types of bass pickups. LOW CUT SWITCH -- CLEAN CHANNEL (8) Passive low frequency roll-off filter that is activated when the button is in the "in" position. [. . . ] xLR JACK (34) A transformer balanced 600 ohm XLR jack is provided for direct patching of the amplifier to recording or sound reinforcement consoles. GROUND LIFT SWITCH (35) Provided to lift the XLR jack ground when hum loops are encountered when patching the amplifier to mixing consoles. Next, connect the output of the device to the Power Amp Input (highquality, shielded cables must be used for these connections). The Preamp Output can also be used to route the line level signal to a mixing console, tape recorder, etc. connect the Preamp Output , using a shielded cable , to an input of the tape recorder , mixer , etc. This patch does not affect the operation of the amplifier. Note: The Preamp Output level is approximately 1 volt RMS and is of relatively low impedance (600 ohms). Any effects device used in this effects loop must be capable of receiving 1 volt input and providing 1 volt output in order to properly drive the power amp. High-quality shielded cables must be used for these connections. All-Tube Power Amplifier: (8) 6550 power tubes Driver: (1) 12AT7 Input Stage and Phase Splitter: (2) 12AX7s Rated Power: 400 watts RMS into 4 or 8 ohm with 120 V AC 60 Hz line Power at Clipping: (typically) 420 watts RMS into 4 or 8 ohm load @1 kHz with 120 V AC line Sensitivity: 1 V RMS/0 dB Hum and Noise: greater than 85 dB below rated power Power Consumption: Domestic: 1000 watts, 50/60 Hz, 120 V AC Export: 1000 watts, 60 Hz, 220-230/240 V AC DDT Power Amplifier Compression: No solid state devices in signal path Input Sensitivity: Clean Channel Nominal: 90 mV RMS / -20. 52 dB Tone Controls: Passive type controls used in both the Clean and Crunch channels Preamp Out/Power Amp In Jacks: Preamp Out Load Impedance: 1 K ohm or greater Nominal Output Level: 1 V RMS / 0 dB Power Amp In Impedance: 22 K ohms Nominal Input Level: 1 V RMS / 0 dB (Switching jack provides Preamp out to Power Amp in connection when not used. Clean Channel Settings: Pre Gain: 5 Low: 5 Mid: 5 Mid Shift: 600 Hz High: 5 Low Cut: Out Low Boost: Out High Boost: out Crunch Channel Settings: Pre Gain: 5 Low: 5 Mid: 5 High: 5 Low Boost: Out High Boost: Out Due to our efforts for constant improvements, features and specifications listed herein are subject to change without notice. This flowchart illustrates signal flow within the unit. In order to thoroughly understand the unit's functions, please study this diagram carefully. Note: Channel Combine Switch may be set in the "in" position to mix the distortion sound with the clean sound. Tone settings given are general and will vary according to the type of guitar, gauge type of the strings, the type of pickup, and even the type of pick. Personal preference, playing style, and type of music greatly contribute to desired tonality. La position « out » sélectionne le canal « clean ». La position « out » selects single channel operation. Les commutateurs de sélection et de combinaison des canaux, situés sur le panneau avant, doivent être en position « out » pour que la pédale à distance fonctionne correctement. [. . . ] All service work should be done by a qualified service technician. This product should be used only with a cart or stand that is recommended by Peavey Electronics. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. [. . . ]