User manual PEAVEY HDH 3 DATASHEET

[. . . ] Connect the line cord to this connector and to a properly grounded AC supply. Damage to the equipment may occur if an improper line voltage is used. ) Never remove or cut the ground pin of the line cord plug. This unit is supplied with a properly rated line cord. [. . . ] INPUT JACK This input will accept signals from all types of bass pickups. iNPUT PAD SWITCH Provided for instruments that have extremely high output , which can result in overdriving (distorting) the input stage. Pressing the switch to its "in" or "active" position reduces the level of the input signal by 10 dB. This jack is buffered off the input jack so it is just like plugging directly into the tuner. When the knob is fully counterclockwise (set to 0), there is no voicing added. The final level adjustment should be made after the desired sound has been achieved. LINE OUT--XLR JACK Provides low impedance, electronically balanced signal for patching into a sound reinforcement or recording console. LINE OUT LEVEL CONTROL Controls the output level of the balanced line out. PRE-/POST-EQ SELECT SWITCH Allows selection between a Pre-EQ (switch set to the "out" position) or a Post-EQ (switch set to the "in" position) send to the XLR line out jack. GROUND LIFT SWITCH Provided to lift the ground on the XLR jack when ground loops are encountered. EFFECTS LOOP REMOTE SWITCH JACK This jack accommodates the remote footswitch (optional part number 00051000 ON/OFF single button switch), which is used to remove the effects loop from the signal path. Using this jack along with the preamp out jack creates a possible second effects loop. 450 Watts RMS with 2 Ohm load 300 Watts RMS with 4 Ohm load RD 170 Watts RMS with 8 Ohm load Set to appropriate level for instrument used NOTE: "DDT should be utilized for maximum speaker protection" Slap Setting In Set to appropriate level for instrument used Doesn't matter when Mid is set to 0 Set as necessary Set to appropriate level for instrument used Mains Fuse = 8 amps Mains Voltage = 120 VAC 60 Hz Power Consumption = 350 watts Hum and noise: Typically greater than -89 dB unweighted with controls set as follows. Pad = out (Passive) Bright = out (Normal) Pre-Gain = 5 (12 o'clock) Contour = 0 (fully counterclockwise) Bass = 0 (12 o'clock) Mid = 0 (12 o'clock) Mid Shift = 0 (12 o'clock) High = 0 (12 o'clock) Master Volume = 10 (fully Clockwise) Line Out Level = 10 (fully Clockwise) Nominal input: 315 mV RMS Minimum input: 28 mV (pre gain and master fully CW) Maximum input: 9 V (maximum signal at input before clipping occurs) Bright boost: + 8 dB @ 5 kHz Contour: Special frequency compensation Bass: ± 15 dB @ 30 Hz, Shelving type Eq Mid : ± 15 dB @ 200 @ 2 kHz (Mid shift control determines center frequency) Mid Shift: 200 to 2 kHz High: ±15 dB @ 8 kHz, Shelving type Eq 82 V RMS) into 2 ohms with no more than 1% THD+N 308 watts (35. 10 V RMS) into 4 ohms with no more than 1% THD+N 177 watts (37. 63 V RMS) into 8 ohms with no more than 1% THD+N Level is dependent on level control setting and pre gain setting Typically greater than 102 dB below full power @ 8 ohms unweighted 315 V RMS) with pre @ 5, Master @ 10 Controlled via footswitch, ground tip to defeat. 61 dB, 100mW to 160 W RMS, 20 Hz to 20 kHz (8 ohm load, typically below 0. 450 Watts RMS with 2 Ohm load 300 Watts RMS with 4 Ohm load RD 170 Watts RMS with 8 Ohm load Set to appropriate level for instrument used NOTE: "DDT should be utilized for maximum speaker protection" Slap Setting In Set to appropriate level for instrument used Doesn't matter when Mid is set to 0 Set as necessary Set to appropriate level for instrument used What This Warranty Does Not Cover The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modification or neglect; (2) damage occurring during shipment; (3) damage caused by repair or service performed by persons not authorized by Peavey; (4) products on which the serial number has been altered, defaced or removed; (5) products not purchased from an Authorized Peavey Dealer. Who This Warranty Protects This Warranty protects only the original retail purchaser of the product. Speakers, baskets, drivers, diaphragm replacement kits and passive crossovers) and all Accessories Tubes and Meters Duration 2 years *(+ 3 years) 2 years *(+ 1 year) 3 years *(+ 2 years) 1 year *(+ 1 year) 2 years 1 year 90 days [*denotes additional warranty period applicable if optional Warranty Registration Card is completed and returned to Peavey by original retail purchaser within 90 days of purchase. What Peavey Will Do We will repair or replace (at Peavey's discretion) products covered by warranty at no charge for labor or materials. If the product or component must be shipped to Peavey for warranty service, the consumer must pay initial shipping charges. [. . . ] install in accordance with manufacturer's instructions. It should not be placed flat against a wall or placed in a built-in enclosure that will impede the flow of cooling air. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ]