User manual PEAVEY L.A. 400

[. . . ] Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit from the apparatus. Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your plug, proceed as follows: a) The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E, the earth symbol, colored green or colored green and yellow. B) The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black. C) The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red. [. . . ] Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Write for our free booklet "Shock Hazard and Grounding. " Connect only to a power supply of the type marked on the unit adjacent to the power supply cord. If this product is to be mounted in an equipment rack, rear support should be provided. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. Government's Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures: According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. 2%) Power consumption: 50 Watts, 50/60 Hz, 120 VAC PREAMP SECTION: The following specs are measured @ 1 kHz with the master EQ flat @ 0 dB. Nominal values are with levels @ 5 Minimum values are with levels @ 10 6 dBV, 93 mV RMS Maximum input level: +12 dBV, 4V RMS Frequency response: +0, -2 dB, 50 Hz to 10 kHz HEADPHONE OUTPUT (Stereo headphone jack, mono signal) Load impedance: 4 Ohms or greater Nominal power output: 20 mW into 4 Ohms (Switching jack disconnects the internal speaker when plug is inserted) Rated power and load: 20 W RMS into 4 Ohms Power @ clipping (typical): (5% THD, 1 kHz, 120 VAC line) 20 W RMS into 4 Ohms Total harmonic distortion: Less than 0. 5% , 100 mW to 12 W RMS , 60 Hz to 10 kHz , 4 Ohms (typically below 0. 2%) Power consumption: 50 Watts, 50/60 Hz, 120 VAC PREAMP SECTION: The following specs are measured @ 1 kHz with the master EQ flat @ 0 dB. Nominal values are with levels @ 5 Minimum values are with levels @ 10 6 dBV, 93 mV RMS Maximum input level: +12 dBV, 4V RMS Frequency response: +0, -2 dB, 50 Hz to 10 kHz HEADPHONE OUTPUT (Stereo headphone jack, mono signal) Load impedance: 4 Ohms or greater Nominal power output: 20 mW into 4 Ohms (Switching jack disconnects the internal speaker when plug is inserted) Rated power and load: 20 W RMS into 4 Ohms Power @ clipping (typical): (5% THD, 1 kHz, 120 VAC line) 20 W RMS into 4 Ohms Total harmonic distortion: Less than 0. 5% , 100 mW to 12 W RMS , 60 Hz to 10 kHz , 4 Ohms (typically below 0. 2%) Power consumption: 50 Watts, 50/60 Hz, 120 VAC PREAMP SECTION: The following specs are measured @ 1 kHz with the master EQ flat @ 0 dB. Nominal values are with levels @ 5 Minimum values are with levels @ 10 6 dBV, 93 mV RMS Maximum input level: +12 dBV, 4V RMS Frequency response: +0, -2 dB, 50 Hz to 10 kHz HEADPHONE OUTPUT (Stereo headphone jack, mono signal) Load impedance: 4 Ohms or greater Nominal power output: 20 mW into 4 Ohms (Switching jack disconnects the internal speaker when plug is inserted) Rated power and load: 20 W RMS into 4 Ohms Power @ clipping (typical): (5% THD, 1 kHz, 120 VAC line) 20 W RMS into 4 Ohms Total harmonic distortion: Less than 0. 5% , 100 mW to 12 W RMS , 60 Hz to 10 kHz , 4 Ohms (typically below 0. 2%) Power consumption: 50 Watts, 50/60 Hz, 120 VAC PREAMP SECTION: The following specs are measured @ 1 kHz with the master EQ flat @ 0 dB. Nominal values are with levels @ 5 Minimum values are with levels @ 10 6 dBV, 93 mV RMS Maximum input level: +12 dBV, 4V RMS Frequency response: +0, -2 dB, 50 Hz to 10 kHz HEADPHONE OUTPUT (Stereo headphone jack, mono signal) Load impedance: 4 Ohms or greater Nominal power output: 20 mW into 4 Ohms (Switching jack disconnects the internal speaker when plug is inserted) What This Warranty Does Not Cover The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modification or neglect; (2) damage occurring during shipment; (3) damage caused by repair or service performed by persons not authorized by Peavey; (4) products on which the serial number has been altered, defaced or removed; (5) products not purchased from an Authorized Peavey Dealer. [. . . ] Who This Warranty Protects This Warranty protects only the original retail purchaser of the product. 2 years *(+ 3 years) 2 years *(+ 1 year) 3 years *(+ 2 years) 1 year *(+ 1 year) 2 years 1 year 90 days [*Denotes additional warranty period applicable if optional Warranty Registration Card is completed and returned to Peavey by original retail purchaser within 90 days of purchase. What Peavey Will Do We will repair or replace (at Peavey's discretion) products covered by warranty at no charge for labor or materials. If the product or component must be shipped to Peavey for warranty service, the consumer must pay initial shipping charges. [. . . ]