User manual PEAVEY MAQ 300

[. . . ] Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer. While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com. Trademark Information Oki and Oki Data are registered trademarks of Oki Electric Industry Company Ltd. [. . . ] DISABLE C330: Enables or disables this network protocol. ENABLE / DISABLE C530: ENABLE / DISABLE NETWARE ETHERTALK ENABLE\ Enables or disables this network protocol. DISABLE 55 ­ C330/C530 Menu Functions ITEM ACTION EXPLANATION FRAME TYPE AUTO / 802. 2 / 802. 3 / ETHERNET II / SNAP AUTO / MANUAL Selects the Ethernet MAC layer frame type. Display Condition: Netware should be enabled. IP ADDRESS SET IPV4 ADDRESS Specifies whether IP address allocation is automatic (DHCP) or manually assigned. xxx. xxx. x Current assigned IP address. To change, xx. xxx press OK and use Menu buttons to increment 1st octet, then press OK again to move on to next octet. When 4th octet has been set, press OK again to register new address. xxx. xxx. x Current assigned gateway address. ENABLE / Enables or disables Web config. DISABLE ENABLE / Enables or disables Telnet config. DISABLE ENABLE / Enables or disables communication via FTP. DISABLE ENABLE / Applies to C330 and C530 only. YES/NO If NO is selected, the previous menu display resumes. If YES is selected, changes made to the menu setting are saved and you exit from the menu. Notes: This cannot be executed when data is printing. This menu item will only show if the menu has been saved previously POWER SAVE ENABLE / Enables or disables automatic power save DISABLE mode. Delay before entering this mode is set in the SYSTEM CONFIGURATION menu. ENABLE / Sets Enable/Disable of Sleep Mode. DISABLE SLEEP PAPER BLACK ­2~0~+2 Used for small adjustments when you expeSET rience faded print or light specks / streaking in monochrome printing on white paper. Select a higher value to reduce fading, or a lower value to reduce specks or streaking in high density print areas. 60 ­ C330/C530 Menu Functions ITEM ACTION EXPLANATION PAPER COLOR ­2~0~+2 As above, but for color printing. SET SMR STTING ­3~0~+3 Sets a correction value for uneven print quality, to correct print variations caused by variations in temperature and humidity or in print density/frequency. ­3~0~+3 Sets a correction value for dark-colored paper printing, to correct print variations caused by variations in temperature and humidity or in print density/frequency. BG SETTING Usage Menu This menu is for information only, and provides an indication of total usage of the printer and the expected life left in its consumable items. This is particularly useful if you do not have a full set of replacement consumables to hand and you need to know how soon you will need them. ITEM EXPLANATION TRAY1 COUNT TRAY2 COUNT MP TRAY COUNT DRUM UNIT LIFE REMAINING BELT LIFE REMAINING FUSER LIFE REMAINING K TONER (n. nK) REMAINING C TONER (n. nK) REMAINING M TONER (n. nK) REMAINING Y TONER (n. nK) REMAINING The total number of pages fed from tray 1. [. . . ] Once you have created the customized curve in the utility, you must save the curve (new PPD) and reconfigure your printer driver to use the new PPD. Network Software Utilities · NIC Setup Utility Use to set up the printer network card. · Direct Network Printing Utility (LPR) For printing on an Ethernet network without the need for a print server. · Network Extension For use when your printer is connected over a TCP/IP network. Check the printer status and configuration from the Printer Properties tab in the printer driver. Optional Utilities · Printer Display Language Use to change the language of the printer's display. [. . . ]