User manual PEAVEY MINX 110

[. . . ] NOTE: The headphone system will not work with headsets equipped with a mono phone plug. POWER SWITCH (9) Depress the switch to the "POWER" position to turn the unit on. LINE CORD­120 V products only (11) For your safety, we have incorporated a 3-wire line (mains) cable with proper grounding facilities. It is not advisable to remove the ground pin under any circumstances. [. . . ] 5 mV RMS Maximum Input Level: +6 dBV, 2 V RMS Preamp Output: (Phone jack ring) Function: High level post EQ send Load Impedance: 10 k ohms or greater Nominal Output Level: 0 dBV, 1 V RMS (at the DDTTM limit of 30 W RMS output) Maximum Output Level: +18 dBV, 8 V RMS Power Amp Input: (Phone jack tip) Function: High level post EQ return Input Impedance: 22 k ohms Designed Input Level: 0 dBV, 1 V RMS Headphone Output: Load Impedance: 4 ohms or greater Nominal Power Output: 100 mW into 4 ohms (Stereo jack, monaural signal, disconnects internal speaker when phone plug is inserted) System Hum & Noise @ Nominal Input Level: (20 Hz to 20 kHz unweighted) 80 dB below rated power Equalization: Low, mid, & high passive type Due to our efforts for constant improvements, features and specifications listed herein are subject to change without notice. Tone settings given are general and will vary according to type of guitar, type and gauges of strings, type of pickup, and even type of pick. Personal taste, playing style, and type of music greatly contribute to desired tonality. PEAVEY ONE-YEAR LIMITED WARRANTY/REMEDY PEAVEY ELECTRONICS CORPORATION ("PEAVEY") warrants this product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from defects in material and workmanship for a period of one (1) year from date of purchase, PROVIDED, however, that this limited warranty is extended only to the original retail purchaser and is subject to the conditions, exclusions, and limitations hereinafter set forth: PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS If this product contains tubes or meters, Peavey warrants the tubes or meters contained in the product to be free from defects in material and workmanship for a period of ninety (90) days from date of purchase; PROVIDED, however, that this limited warranty is extended only to the original retail purchaser and is also subject to the conditions, exclusions, and limitations hereinafter set forth. cONDITIONS , EXCLUSIONS , AND LIMITATIONS OF LIMITED WARRANTIES These limited warranties shall be void and of no effect , if: a. The first purchase of the product is for the purpose of resale; or b. The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER; or c. The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance, or other causes not arising out of defects in material or workmanship; or d. the serial number affixed to the product is altered , defaced , or removed. In the event of a defect in material and/or workmanship covered by this limited warranty, Peavey will: a. , cases involving anything other than covers, footswitches, patchcords, tubes or meters), repair the defect in material or workmanship or replace the product, at Peavey's option; and provided, however, that, in any case, all costs of shipping, if necessary, are paid by you, the purchaser. It should not be placed flat against a wall or placed in a built-in enclosure that will impede the flow of cooling air. This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord. Never break off the ground pin on the power supply cord. For more information on grounding, write for our free booklet "Shock Hazard and Grounding. Power supply cords should always be handled carefully. Never walk or place equipment on power supply cords. Periodically check cords for cuts or signs of stress, especially at the plug and the point where the cord exits the unit. The power supply cord should be unplugged when the unit is to be unused for long periods of time. If this product is to be mounted in an equipment rack, rear support should be provided. Metal parts can be cleaned with a damp rag. [. . . ] This unit should be checked by a qualified service technician if: a. Anything has fallen or been spilled into the unit. The unit has been dropped or the enclosure damaged. The user should not attempt to service this equipment. [. . . ]