User manual PEAVEY ROADMASTER

[. . . ] Copyright Information Copyright 2001 by Oki Data. Revised edition, 2001 Written and produced by the Oki Data Training and Publications Department. Contact Information Please address any comments on this publication to: Mailing Address Oki Data Americas, Inc. Laurel, NJ 08054-4620 e-Mail Address pubs@okidata. com Web Site Please visit Oki Data's multilingual web site at: http://www. okidata. com Trademark Information PEAVEY and MICROLINE are registered trademarks of Oki Electric Industry Company, Ltd. Energy Star is a registered trademark of the United States Environmental Protection Agency Epson is a registered trademark of Epson America, Inc. [. . . ] Automatic Forms Tear-Off automatically moves the paper from the initial printing position (print start position) to the tear-off position, after a time interval which you select through the menu. The top of the page (perforation) is even with the tear bar. The tear bar is located under the clear top of the access cover. Paper remains in the tear-off position until the printer receives more data. Then, the paper moves back down for printing (retracts to the initial print position). When printing stops, the paper advances to the tear-off position. TEAR Key and Automatic Forms Tear-Off If you press TEAR (1) when Forms Tear-Off is turned on (activated in the printer menu), the printer retracts the paper to the Top of Form position. 1 32T-FP. eps SEL SEL MENU SHIFT LF Micro Feed Down ! The status of the Forms Tear-Off menu setting affects how you set the Top of Form. To determine the status of the Forms Tear-Off menu setting, refer to "Using Your Printer, Top of Form, Forms Tear-Off Status (ON or OFF). " For information on setting the Top of Form, refer to "Using Your Printer, Top of Form, Setting Top of Form, Forms Tear-Off (ON or OFF). " !! If the software package you are using "pauses" while sending data to the printer, Forms Tear Off may be activated (if it is enabled through the Menu). The pause must be for two or more seconds. 5 Press FF/LOAD. 1 32T-11. eps and Turbo-1. eps 1 2 3 4 5 2 54 | Microline 390/391 Turbo Printhead Gap The printhead gap is the distance between the printhead and the platen. Make sure the printer is turned off before you open the access cover. Media 12-20 lb paper 20-24 lb bond paper Labels Envelopes 2-part form (with carbon) 3-part form (with carbon) 4-part form (with carbon) 5-part form (with carbon) 6-part form (with carbon) Setting 1 2 3 or 4 4 or 5 1 or 2 2 or 3 3 or 4 4 or 5 5 ! To adjust the gap, open the access cover and move the blue lever (1) to the recommended setting from the table. 32T-35. eps 1 ! For dedicated, bottom-feed printing of extra-thick continuous forms (requires optional push and/or pull tractor), the printhead gap range can be expanded to take forms up to 0. 031" (0. 79 mm) thick. For more information, refer to "Using Your Printer, Printhead Gap, Expanded Printhead Gap. " User's Guide: English | 55 Expanded Printhead Gap Your printer can be used for dedicated bottom-feed printing on extra-thick multi-part forms. Extra-thick multi-part forms range from 0. 017-inch (0. 43 mm) to a maximum of 0. 03 inch (0. 79 mm). To print on extra-thick multi-part forms, you engage the expanded printhead gap feature. This expands the head gap settings for extra-thick forms and heavy card stock. It also increases the impact strength of the pins in the printhead. To engage the expanded printhead gap: 1 Turn the printer off. 2 Remove the access cover and the pull-up roller assembly. 32T-02. eps and 32T-04UP. eps SEL ! CAUTION!Once the expanded printhead gap is engaged, you cannot print on single sheets without changing the gap back. [. . . ] -- Liquid has been spilled into the housing, or the printer has been exposed to water. -- The printer has been dropped or its cabinet has been damaged. -- The printer doesn't function normally when you're following the operating instructions. 118 | Microline 390/391 Turbo ENERGY STAR® Regulatory Information Year 2000 Compliance This product is Year 2000 Compliant. It contains information technology that accurately processes date and time data between the years 1999 and 2000, and carries no issue for the September 9, 1999 (9999) programming concern. [. . . ]