User manual PEAVEY STADIA II DATASHEET

[. . . ] Please address any comments on this publication to: Training & Publications Department Okidata, Division of Oki America, Inc. All products currently sold by Okidata are Year 2000 Compliant. Each product contains information technology that accurately processes date and time data between the years 1999 and 2000. These products, when used in combination with products purchased from other manufacturers, whose products properly exchange date and time information, will accurately process the date and time. [. . . ] to activate it , hold the SHIFT button and press the SEL button to enter the Menu Mode (1). Press the LF button until the Rear Feed group appears (2), press the FF/LOAD button until Form Tear-Off appears (3), press the TEAR button (4) until the setting you want appears -- 500 ms, 1 sec, or 2 sec -- then hold the SHIFT button while pressing the SEL button to exit the Menu Mode (1). Do not engage Form Tear-Off when printing on labels. To adjust the tear position with the Forms Tear-Off feature engaged, press and hold the SHIFT button while using the LF button (1) to feed the paper down in small increments or the FF button (2) to feed the paper up in small increments. To set the Top of Form with the FormTear-Off feature engaged, push and hold the SHIFT and TEAR buttons (3) to see the current Top of Form setting. Then continue to hold the SHIFT button, release the TEAR button and press the LF button (4) to move the paper down or the FF button (5) to move the paper up to set the Top of Form. If the pause lasts more than two seconds, the paper advances to the tear-off position until more data is received. No data is lost, but this extra paper movement can cause uneven print registration in graphics. If you have this problem, enter the printer Menu, go to the Rear Feed group and change the setting for Form Tear-off to Off. If you have problems setting the Top of Form high enough on the page when using Forms TearOff, see "Problem Solving" in Chapter 6. Press the PARK button (1) to move continuous-form paper out of the paper path. To place your printer in the Menu Mode, hold the SHIFT button while pressing the SEL button. The MENU light comes on and the SEL light goes out. When you are done making changes in the Menu Mode, exit the mode (saving the changes you have made) by holding the SHIFT button while pressing the SEL button. The MENU light goes out and the SEL light comes on. MENU light glows when printer is in Menu Mode. Within each group is a list of items, each of which has various settings. The illustration at the right shows a printout of the factory settings for the menu. To generate a printout of the menu, hold the SHIFT button and press the SEL button to enter the Menu Mode, then press the PARK button. For a table showing the settings for each item within each group, see the Reference Section at the back of this manual. Active Buttons in Menu Mode 1 GROUP Button: Each time you press this button, the menu line that prints shows the next group. 2 ITEM Button: Each time you press this button, the menu line that prints shows the next item within that group. [. . . ] 6000 hours at 25% duty cycle and 35% page density 15 minutes 200 million characters average in 10 cpi utility mode at 25% duty and black ribbon: 4 million characters color ribbon: black = 1. Feed Top only Rear, Bottom Rear, Bottom Rear, Bottom Bottom only Top Rear, Bottom Bottom only Top only Weight 14 to 24 lb. 5" ML 590: size 5" x 8" ML 591: size 5" x 14" 8. Paper type Cut sheets Single-part continuous forms Carbonless, multi-part continuous form (original + 4 copies) Interleaf, multi-part continuous forms (original + 4 copies) Labels Envelopes, single feed Envelopes, continuous feed, non-overlap type Card stock Transparencies 5%, -15%), 50 or 60 Hz (±2%) Also available for 230/240 volts ac (+10%, -14%), 50 or 60 Hz (±2%) Specifications subject to change without notice. [. . . ]