User manual PEAVEY SUPREME XL

[. . . ] A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is provided for your safety. [. . . ] Capable of over 100 Watts of earth shaking power into any standard guitar cabinet, this behemoth can blow the roof off the largest of venues or. With a twist of the master volume and a flip of the 25/50/100 Watt power level switch, keep a crowd in the smallest of bars. Further tonal mayhem can be accomplished with outboard effects via the foot-switchable effects loop. reverb is also included to put the icing on the cake. We've even thrown in a footswitch and a classic jeweled pilot light so that you will certainly have the tools to break ALL of the rules. The all new Peavey Supreme XL--now you don't have anymore excuses. You can just hook the Supreme XL up to your favorite cabinet, plug in and go. Or better yet, read through this operating guide and get the most out of your amplifier. Be sure to hook up correctly so you don't damage yourself or your equipment. Bottom, body, and edge along with active EQ on Lead channel · It illuminates when mains power is being supplied to the amp and looks really cool at the same time!Once the desired balance between both channels in the amplifier has been achieved, the entire output level of the unit can be increased or decreased by rotating this control. (5 & 12) VOLUME These controls set the overall level for each respective channel. (10 & 17) GAIN This control adjusts the input volume level of each respective channel. The footswitch cable should be connected before the amp is powered up. PREAMP OUT The preamp out can be used to route the amplified signal from the preamp to a mixing console, tape recorder, etc. Connect the preamp output to line-level inputs of other equipment using a high-quality shielded cable. This patch does not affect operation of the amplifier. Connect the power amp input to line-level output of other equipment using high-quality shielded cable. [. . . ] Left Field: Damping = Tight; Power = 25 watts; neck and middle single-coil; Master Volume and Reverb set as desired 80 W into 16 ohms 100 W into 8 ohms 100 watts RMS into 8 ohms; 80 watts RMS into 16 ohms 80 watts RMS into 16 ohms @ 5% THD; 1 kHz; 120 VAC line Greater than 98 dB below rated power (Clean channel, Modern, 20 Hz­20kHz unweighted) Greater than 64 dB below rated power Rhythm channel: Low, Mid and High passive EQ with three distinct voicings Lead channel: Bottom, Body and Edge active EQ with three distinct voicings The following specifications are measured @ 1kHz with the controls preset as follows: Low and High EQ @ 10; Mid EQ @ 0 Lead Volume @ 5 Bottom EQ @ 10 Body and Edge EQs @ 5 Master Volume @ 10 Reverb @ 0 Nominal Levels are with Gain @ 5; Volume @10 Minimum Levels are with Gain @ 10; Volume @ 10 Damping @ Tight Power @ 100 watts N o t e : For proper ventilation, allow 24" clearance from nearest conbustible surface. 100 watts RMS into 8 ohms; 80 watts RMS into 16 ohms 80 watts RMS into 16 ohms @ 5% THD; 1 kHz; 120 VAC line Greater than 98 dB below rated power (Clean channel, Modern, 20 Hz­20kHz unweighted) Greater than 64 dB below rated power Rhythm channel: Low, Mid and High passive EQ with three distinct voicings Lead channel: Bottom, Body and Edge active EQ with three distinct voicings The following specifications are measured @ 1kHz with the controls preset as follows: Low and High EQ @ 10; Mid EQ @ 0 Lead Volume @ 5 Bottom EQ @ 10 Body and Edge EQs @ 5 Master Volume @ 10 Reverb @ 0 Nominal Levels are with Gain @ 5; Volume @10 Minimum Levels are with Gain @ 10; Volume @ 10 Damping @ Tight Power @ 100 watts N o t e : For proper ventilation, allow 24" clearance from nearest conbustible surface. 100 watts RMS into 8 ohms; 80 watts RMS into 16 ohms 80 watts RMS into 16 ohms @ 5% THD; 1 kHz; 120 VAC line Greater than 98 dB below rated power (Clean channel, Modern, 20 Hz­20kHz unweighted) Greater than 64 dB below rated power Rhythm channel: Low, Mid and High passive EQ with three distinct voicings Lead channel: Bottom, Body and Edge active EQ with three distinct voicings The following specifications are measured @ 1kHz with the controls preset as follows: Low and High EQ @ 10; Mid EQ @ 0 Lead Volume @ 5 Bottom EQ @ 10 Body and Edge EQs @ 5 Master Volume @ 10 Reverb @ 0 Nominal Levels are with Gain @ 5; Volume @10 Minimum Levels are with Gain @ 10; Volume @ 10 Damping @ Tight Power @ 100 watts N o t e : For proper ventilation, allow 24" clearance from nearest conbustible surface. [. . . ]