User manual PEAVEY T-MAX

[. . . ] The master volume adjustment should be made after the desired sound has been achieved. This LED indicates (when lit) that the input gain stage is being overdriven (distorted). Depressing the input pad switch to its "in" position or reducing the pre gain will alleviate this problem. The "in" position of this switch routes the signal through the graphic equalizer. [. . . ] The preamp output can be used to route the amplified signal to a mixing console, tape recorder, etc. connect the preamp output using a shielded cable to an input of the tape recorder , mixer , etc. This patch does not affect the operation of the amplifier. Signal level is adjusted by the master volume control and the crossover balance control. Signal level is adjusted by the master volume control and the crossover balance control. Selects the effects loop operating level: -10 dBV (3 V RMS) when in low position and 0 dBV (1 V RMS) when in high position. 200 W RMS into 8 ohms 350 W RMS into 4 ohms 500 W RMS into 2 ohms Greater than 95 dB below rated power 35 dB from input jack, -20 dB from full range output (-10 dB Pad Out) Post EQ: -7 dB nominal, +15. 5 dB maximum Note: Post EQ balanced output taken before master volume, Pre EQ balanced output buffered off input jack. All measurements are with the following settings except where noted. Note: Tube channel is designed to produce distortion when pre gain control is set greater than 3 (dependent on input signal). Set Pre and Post Gain so that clip indicator does not light; then use Master Volume for playing level. NOTES FOR TUBE CHANNEL: Distortion: Set Pre Gain very high -- usually above 5. Clean: Set Post Gain @ 10 and set Pre Gain low -- below 5. For further information on other Peavey products, ask your Authorized Peavey Dealer for the appropriate Peavey catalog/publication: Bass Guitars Guitars Bass Amplification Guitar Amplification Sound Reinforcement Enclosures Microphones Keyboards DJ Lighting Mixers, Powered/Non-Powered Accessories/Cables Effects Processors AxcessTM Wear The Peavey BeatTM Monitor® Magazine Key IssuesTM Low DownTM PMTM Magazine PEAVEY ONE-YEAR LIMITED WARRANTY/REMEDY PEAVEY ELECTRONICS CORPORATION ("PEAVEY") warrants this product, EXCEPT for covers, footswitches, patchcords, tubes and meters, to be free from defects in material and workmanship for a period of one (1) year from date of purchase, PROVIDED, however, that this limited warranty is extended only to the original retail purchaser and is subject to the conditions, exclusions, and limitations hereinafter set forth: PEAVEY 90-DAY LIMITED WARRANTY ON TUBES AND METERS If this product contains tubes or meters, Peavey warrants the tubes or meters contained in the product to be free from defects in material and workmanship for a period of ninety (90) days from date of purchase; PROVIDED, however, that this limited warranty is extended only to the original retail purchaser and is also subject to the conditions, exclusions, and limitations hereinafter set forth. cONDITIONS , EXCLUSIONS , AND LIMITATIONS OF LIMITED WARRANTIES These limited warranties shall be void and of no effect , if: a. The first purchase of the product is for the purpose of resale; or b. The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER; or c. The product has been damaged by accident or unreasonable use, neglect, improper service or maintenance, or other causes not arising out of defects in material or workmanship; or d. the serial number affixed to the product is altered , defaced , or removed. In the event of a defect in material and/or workmanship covered by this limited warranty, Peavey will: a. [. . . ] It should not be placed flat against a wall or placed in a built-in enclosure that will impede the flow of cooling air. This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord. Never break off the ground pin on the power supply cord. [. . . ]