User manual PENTAX 6X7 90MM F/2.8 LEAF SHUTTER LENS

[. . . ] Images taken with the purpose of obtaining copyrights also cannot be used outside the scope of use of the copyright as laid out in the Copyright Act, and care should be taken here also. Regarding trademarks PENTAX and Optio are trademarks of HOYA CORPORATION. This product supports PRINT Image Matching III. PRINT Image Matching enabled digital still cameras, printers and software help photographers to produce images more faithful to their intentions. [. . . ] Saving the EV Compensation value setting 1p. 97 Setting the Sensitivity You can select the sensitivity to suit the brightness of the surroundings. Auto The sensitivity is automatically adjusted by the camera. (Sensitivity 100 - 800) 100 The lower the sensitivity, the less noise that affects the image. The 200 shutter speed will be slower in low light conditions. 400 800 1600 Higher sensitivity settings use faster shutter speeds in low light 3200 conditions to reduce camera shake, but the image may be affected by noise. 6400 1 2 3 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [Sensitivity]. Press the four-way controller (5). A pull-down menu appears. 4 Use the four-way controller (23) to change the sensitivity. Rec. Mode Recorded Pixels Focusing Area Sensitivity EV Compensation Movie Digital Zoom MENU Cancel 1/2 Auto 100 200 400 800 OK OK 5 6 Press the 4 button. The setting is saved. Press the 3 button. The camera returns to capture status. · When Sensitivity is set to 3200 or 6400, the number of recorded pixels is fixed at f. · When set to 9 (Green) or C (Movie) mode, only Auto (sensitivity 100 - 800) is available. · When set to c (Digital SR) mode, only Auto (sensitivity 100 - 6400) is available. Saving the sensitivity setting 1p. 97 3 Taking Pictures Setting the Date Imprint Function You can choose whether to imprint the date and/or time when taking still pictures. 1 2 3 Press the 3 button in A mode. The [A Rec. Mode] appears. Use the four-way controller (23) to select [Date Imprint]. Press the four-way controller (5). A pull-down menu appears. 91 4 Use the four-way controller (23) to select the Date Imprint details. Choose from [Date], [Date & Time], [Time] or [Off]. Rec. Time 15:02:26 Recorded Pixels 12805 15 1 640 Movie SR 24 640 15 320 24 320 15 MENU Cancel OK OK 7 8 Press the 4 button. The setting is saved. Press the 3 button twice. The camera returns to capture status. 95 Setting the Movie SR (Movie Shake Reduction) Function In C (Movie) mode, you can compensate for camera shake while you are recording a movie with the Movie SR (Movie Shake Reduction) function. 1 3 Taking Pictures 96 Press the 3 button in A mode. The [A Rec. Mode] menu appears. 2 3 4 5 Use the four-way controller (23) to select [Movie]. Press the four-way controller (5). The [Movie] screen appears. Use the four-way controller (23) to select [Movie SR]. Use the four-way controller (45) to select O (On) or P (Off). The setting is saved. Movie Recorded Pixels Movie SR 640 24 MENU 6 Press the 3 button twice. The camera returns to capture status. The Movie SR function cannot be used when the recorded pixels is set to F (1280×720 pixels, 15fps). Saving the Settings (Memory) The Memory function is for saving the current camera settings when the camera is turned off. For some camera settings, the Memory function is always set to O (On) (the settings are saved when the camera is turned off), while for others you can choose on or off (to choose whether the settings are saved or not when the camera is turned off). The items which can be set to O (On) or P (Off) in the Memory function are shown in the table below. (Items not listed here are always saved in the selected settings when the camera is turned off. ) If you select O (On), the settings will be saved in the status they were in immediately before the camera was turned off. If you select P (Off), the settings will be reset to the defaults when the camera is turned off. The table below also shows whether the Memory default setting for each item is on or off. Default Page Setting Face Priority A Face Recognition mode set by using the I button. P p. 61 Flash Mode The flash mode set with the four-way controller (4) O p. 84 p. 78 Drive Mode The drive mode set with the four-way controller (2) P p. 79 Focus Mode The focus mode set with the four-way controller (5) P p. 86 Zoom Position The zoom position set with the Zoom/w/x button P p. 67 Sensitivity The [Sensitivity] setting on the [A Rec. Mode] menu P p. 90 EV The [EV Compensation] setting on the P p. 89 Compensation [A Rec. Mode] menu The [Digital Zoom] setting on the [A Rec. Mode] Digital Zoom O p. 69 menu The information display mode set with the DISPLAY P p. 18 4/W button If a new SD Memory Card is inserted when On has O -- File No. been selected, file numbers are assigned sequentially. Item Description 3 Taking Pictures 97 1 2 3 4 3 Taking Pictures 98 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [Memory]. [. . . ] 100, 111 Destination . . . . . . . . . . . . . . . . . . . . . . 143 Digital Filter . . . . . . . . . . . . . . . . . . . . . 125 Digital SR . . . . . . . . . . . . . . . . . . . . . . . . . . 78, 79 G Green Button . . . . . . . . . . . . . . . 45, 47 Green Mode . . . . . . . . . . . . . . . . . . . . . . . 66 Guide Indications . . . . . . . . . . . . . . . 23 H Half-length Portrait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Hometown . . . . . . . . . . . . . . . . . . 40, 143 I Image Recovery . . . . . . . . . . . . . . . 114 Image Storage Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 Infinity s . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Info Display . . . . . . . . . . . . . . . . . . . . . . . . 20 Installing a battery . . . . . . . . . . . . . . 27 Installing the Software . . . . . 158 Intelligent zoom . . . . . . . . . . . . . . . . . . 67 E Error messages . . . . . . . . . . . . . . . [. . . ]