User manual PENTAX ESPIO 60V

[. . . ] AE metering sensor 12. Lens/lens cover EN-2 13. Strap eyelet 14. Film take-up spool 15. Ready LED 16. Viewfinder eyepiece 17. Film rewind shaft 18. Film chamber 19. Film check window 20. Back cover 21. Battery cover 22. Tripod socket 23. Back cover latch EN-3 EN-4 CONTENTS NAMES OF PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 WARRANTY POLICY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 FOR SAFE USE OF YOUR CAMERA. . . . . . . . . . . . . . . 9 PRECAUTIONS FOR YOUR CAMERA. . . . . . . . . . . . 10 ATTACHING THE STRAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 INSERTING THE BATTERY. . . . . . . . . . . . . . . . . . . . . . . . . . . 15 CHECKING THE BATTERY. . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 LOADING THE FILM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 AUTO POWER OFF SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . 17 HOLDING THE CAMERA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 TAKING A PICTURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 AUTOMATIC FLASH PHOTOGRAPHY. . . . . . . . . . . . . 19 MODE SELECTION & LCD PANEL . . . . . . . . . . . . . . . . . 20 AUTO FLASH MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 RED-EYE REDUCTION MODE. . . . . . . . . . . . . . . . . . . . . . 21 FLASH-OFF MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 FILL-IN FLASH MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 SELF-TIMER MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 AUTO FILM REWIND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 MID-ROLL REWIND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 AUTO-DATE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 DATE IMPRINTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 DATE AND TIME ADJUSTMENT. . . . . . . . . . . . . . . . . . . . . 25 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 EN-5 WARRANTY POLICY All Pentax cameras purchased through authorized bona fide photographic distribution channels are guaranteed against defects of material or workmanship for a period of twelve months from date of purchase. Service will be rendered, and defective parts will be replaced without cost to you within that period, provided the equipment does not show evidence of impact, sand or liquid damage, mishandling, tampering, battery or chemical corrosion, operation contrary to operating instructions, or modification by an unauthorized repair shop. [. . . ] The protruding part of the strap adjustment clip can be used to press the small buttons on the camera. 3. Close the cover by pushing it back till it locks firmly. Remove the batteries from the camera when you do not expect to use it for a long period time. FOR THE DATE MODEL Set the date and time. Refer to the DATE IMPRINTING. INSERTING THE BATTERY 1. Push the battery cover toward the open direction and open the cover. Insert the two AA batteries according to the polarity information of the battery cover. EN-15 CHECKING THE BATTERY The battery condition in camera can be checked when you turn the power on. The full battery mark ( ) is displayed when the battery is in good condition. The half battery mark ( ) is displayed when the battery is nearly exhausted. The blank battery mark ( ) is displayed when the battery is too low. All functions are locked and the battery mark and film counter blink. Replace the battery immediately. EN-16 LOADING THE FILM This camera is designed to use DX-coded films of ISO 100-400. Your camera automatically sets the correct film speed. Slide the back cover latch upward to open. Load the film cartridge into the film chamber and pull out the film enough to reach the FILMTIP mark inside the camera. The film advances to the first frame and "1" is displayed on the LCD panel. (Fig. 7) If " " blinks on LCD panel, it indicates film loading failure. (Fig. 8) Whether the film is in camera or not can be confirmed by either the film check window or the film counter on the LCD panel. Automatic film loading can be done no matter if power is on or off. AUTO POWER OFF SYSTEM The camera is turned on and left unused for five minutes, the lens automatically retracts and the power is turned off to save the battery energy. HOLDING THE CAMERA (Fig. Keep your elbows close to your body to hold the camera steady. Whether for vertical or horizontal photography, hold the camera with both hands. If the flash is used with the camera held EN-17 vertically, the flash unit should be positioned above the lens. If the flash is used while holding the camera with the flash positioned below the lens the result will look unnatural. [. . . ] Press the SELECT button to choose the number blinking. Press the SET button to change the number blinking. Press the SET button repeatedly until the desired number is set. until the year, month and day are all correct. [. . . ]