User manual PENTAX ESPIO 838

[. . . ] Creating / Selecting a Job File To create a new job file: POWER TOPO LITE MAIN MENU FILE F1 TO 123 F4 ENT input a new job name by using ENT F1 F5 , 0 9 DEF . Or to select a job file: POWER TOPO LITE MAIN MENU FILE F1 F4 ENT x2 ENT x2 select a job file by F1 F4 NOTE: Once a job file is created or selected, it is effective until a new job file is created or another job file is selected. The default job file "PENTAX" is provided permanently so that data is stored even when no user defined job file exists. 3. Input a Known Point Coordinate To input and store a known point coordinate; POWER TOPO LITE MAIN MENU VIEW F3 TO 123 F4 ENT x2 ENT input a Point Name by using repeat to input value F1 ESC F5 , 0 SAVE F1 9 DEF . ESC to quit x2 input PC (point code) ENT 9 NOTE: There are other functions in VIEW menu; Graphical View, Edit Rectangular Data, and Edit Polar Data. For detail of these functions, please refer to the instruction manual of PowerTopoLite. To input PC (point code): move cursor to PC ENT ENT select a PC from the list by TO 123 F1 F5 ENT F1 F4 x2 input a new PC by 0 9 DEF . NOTE: PC list is displayed only when point codes are stored in the job named "PointColeList" "PointCodeList" job can be . [. . . ] 4. 2 Orientation (Station Point H. Angle Setup) To input a given angle: INPUT F2 input value by using 0 9 DEF . ENT x2 MEASUREMENT SCREEN Or to set the angle 0°: 0 SET F1 x2 ENT MEASUREMENT SCREEN Or to calculate by the Back Sight Point: BSP F5 input value or select from the list ENT MEASUREMENT SCREEN LIST F2 ENT ACCEPT F5 aim Back Sight Point 11 4. 3 Measurement To select the Target type: PAGE F5 x2 repeat TARGET F2 until the desired target type is selected PAGE F5 NOTE: You can check the selected target type at the left side of the Battery mark in the top line of the screen. To measure: Or to start tracking: MEAS F1 MEAS F1 x2 PAGE F5 NOTE: EDM measurement mode can be changed by EDM F1 x2 select and change the EDM mode To input the point information: EDIT F4 move cursor by input values by using F3 , F4 TO 123 , , ENT F1 F5 ESC 0 9 DEF . ACCEPT F5 ENT RETURN TO THE MEASUREMENT SCREEN ENT repeat to input value to quit input point code To save the point information: SAVE F2 (next measurement) Or to measure and save: ME/SAVE F3 (next measurement) NOTE: the Point number is automatically incremented or decremented to make rapid continuous measurements possible. 12 4. 4 Offset Measurement For Radial Offset (the horizontal distance offset along the line of measurement): MEASUREMENT SCREEN PAGE F5 OFFSET F2 ENT input value by using RETURN TO THE MEASUREMENT SCREEN 0 9 DEF . ENT ESC ACCEPT F5 For Tangential Offset: MEASUREMENT SCREEN PAGE F5 OFFSET F2 F4 x3 ENT ENT input value by using , 0 9 DEF . RETURN TO THE MEASUREMENT SCREEN For Distance Offset (slope distance): MEASUREMENT SCREEN PAGE F5 OFFSET F2 F4 x2 ENT ENT input value by using , 0 9 DEF . ESC ACCEPT F5 RETURN TO THE MEASUREMENT SCREEN NOTE: The Offset values are cleared once the measurement is saved. 4. 5 Remote measurement To enter the Remote mode: MEASUREMENT SCREEN PAGE F5 REMOTE F1 x2 PAGE F5 ACCEPT F5 ENT x2 MEAS F1 SAVE F2 RETURN TO THE MEASUREMENT VALUES ARE UPDATED BY TURNING THE TELESCOPE EDIT F4 Input PN, PH ESC (next measurement) input PC or MEASUREMENT SCREEN MEAS F1 PAGE F5 ESC REMOTE F1 ACCEPT F5 ENT x2 REMOTE MODE MEASUREMENT VALUES ARE UPDATED BY TURNING THE TELESCOPE EDIT F4 Input PN, PH SAVE F2 (next measurement) input PC 13 NOTE: Remote values are calculated based on the assumption of the reference plane. Three types of the reference plane are available in PowerTopoLite; Cylindrical surface, Fixed plane (default) and Rotated plane. To change the reference plane type: POWER TOPO LITE MAIN MENU PAGE F5 x2 PREF F4 F4 x4 ENT ACCEPT F5 ENT select by using F3 , F4 To quit the Remote mode: PAGE F5 REMOTE F1 x2 MEASUREMENT SCREEN 5. Polar Coordinate Measurement POWER TOPO LITE MAIN MENU MEAS F2 F4 ENT STATION POINT SETUP 5. 1 Station Point Setup To input the point information: ENT input Point Name by ESC TO 123 F1 F5 , F1 0 9 DEF . H. ANGLE SETUP ENT repeat to input value to quit SAVE or confirm "ppm" ENT NOTE: Input items are PN (point name), IH (instrument height), PC (point code), TEMP (temperature), PRESS (atmospheric pressure) and ppm. "TEMP" and "PRESS" can be input only when "Atmospheric Correction" is set to "ATM INPUT". "ppm" can be input only when "Atmospheric Correction" is set to "ppm INPUT". The input item (cursor position) may be selected by F3 , ENT F4 14 5. 2 Orientation (Station Point H. Angle Setup) Only when the orientation of the horizontal angle is required, proceed according to the following procedure. Otherwise, just pass this step by ENT To input a given angle: INPUT F2 input value by using 0 9 DEF . ENT x2 MEASUREMENT SCREEN Or to set the angle 0°: 0 SET F1 x2 ENT MEASUREMENT SCREEN Or to calculate by Inverse: INVERS F5 LIST F2 ENT LIST F2 select Start Point from the List ENT ACCEPT F5 ENT ENT ACCEPT F5 select End Point from the List x2 MEASUREMENT SCREEN 5. 3 Measurement To select the Target type: PAGE F5 x2 repeat TARGET F2 until the desired target type is selected PAGE F5 NOTE: You can check the selected target type just at the left of the Battery mark in the top line of the screen. To measure: Or to start tracking: MEAS F1 MEAS F1 x2 NOTE: EDM measurement mode can be changed by PAGE F5 x2 EDM F1 select and change the EDM mode 15 To input the point information: EDIT F4 ENT input Point Name by ESC TO 123 F1 F5 , 0 9 DEF . ENT repeat to input value to quit (point code) ACCEPT F5 ENT RETURN TO THE MEASUREMENT SCREEN Input PC To save the point information: SAVE F2 (next measurement) Or to measure and save: ME/SAVE F3 (next measurement) NOTE: The point number is automatically incremented or decremented for rapid continuous measurements. 5. 4 Offset measurement For Radial Offset (horizontal distance offset along with the line of measurement): MEASUREMENT SCREEN PAGE F5 OFFSET F2 ENT input value by using RETURN TO THE MEASUREMENT SCREEN 0 9 DEF . ENT ESC ACCEPT F5 For Distance Offset (slope distance offset): MEASUREMENT SCREEN PAGE F5 ENT OFFSET F2 ESC ENT input value by using RETURN TO THE MEASUREMENT SCREEN 0 9 DEF . ACCEPT F5 NOTE: The Offset values are cleared once the measurement is saved. 16 6. Free Stationing POWER TOPO LITE MAIN MENU FREE F4 input Inst. Height (IH) by using 0 9 DEF . ENT KNOWN POINT SETUP 6. 1 Known Point setup Select the point from the stored data: LIST F2 select the point by FIND PN F2 F4 ENT ACCEPT F5 MEASUREMENT SCREEN Or input PN which is already stored in memory to call and display the known coordinate. ANGLE SETUP ENT repeat to input value to quit ACCEPT or confirm "ppm" ACCEPT F5 Orientation (Station Point Setup): INPUT F2 input value by using 0 9 DEF . ENT x2 SIDE SHOTS or to set the angle 0°: 0 SET F1 x2 ENT SIDE SHOTS or to calculate by the known points (Start point and End point): INVERS F5 LIST F2 ENT LIST F2 select Start Point from the List ENT ACCEPT F5 ENT ENT ACCEPT F5 select End Point from the List x2 SIDE SHOTS Side shot measurement: repeat MEAS F1 , EDIT F4 , SAVE F2 MEAS F1 for all side shots , EDIT F4 finish measurements by , ENT at the Corner Point ESC TRAVERSE MENU 23 NOTE: The corner point is the foresight of the traverse, which is ENT the next instrument point and must be ended by If required, select the target by PAGE F5 x2 TARGET F2 before each measurement. 9. 2 Measurement at a Corner Point TRAVERSE MENU ENT F4 Station Setup: (the last corner point is displayed as Station) ACCEPT F5 NOTE: Input Instrument Height (IH), if necessary. Orientation: (sight the back sight point) ENT Side shot: repeat MEAS F1 , EDIT F4 , SAVE F2 MEAS F1 for all side shots , EDIT F4 finish measurements by , ENT at the Corner Point ESC TRAVERSE MENU NOTE: The corner point is the foresight of the traverse, which is ENT the next instrument point and must be ended by . If required, select the target by PAGE F5 x2 TARGET F2 before each measurement. 24 9. 3 To finish the traverse measurement Fixed traverse: Measure the known point and press corner point. ENT ENT at the last Closed traverse: Measure the start point and press at the last corner point with the different Point Name. NOTE: Use a different point name (PN) when you measure the start point as the last corner point. For example, change "T1" to "T1-1" etc. Open traverse: The closing errors are not calculated. No need to end the measurement by pressing ENT . 9. 4 Traverse Calculation To Start Fixed traverse calculation: TRAVERSE MENU F4 x2 ENT NOTE: To select CLOSE TRAVERSE CALC. : To select OPEN TRAVERSE CALC. : Start Point Coordinate setup: LIST F2 F4 x3 x4 F4 select the point by FIND PN F2 F4 ENT ACCEPT F5 END POINT SETUP or to input the known coordinate; ENT input Point Name by ESC TO 123 F1 F5 ACCEPT F5 , 0 9 DEF . ENT input the next value or to quit END POINT SETUP 25 End Point Coordinate setup: the same operation as in the above. NOTE: The End Point Coordinate Setup is required only in the fixed traverse. Result of Traverse Calculation: To see the result of each corner point: To see all points in order: To save all results: F1 or or F2 F3 F4 ACCEPT F5 TRAVERSE MENU 10. Cogo To access COGO menu and select calculation type: POWER TOPO LITE MAIN MENU PAGE F5 CALC F2 ENT select calc. type by F3 or F4 ENT Input required parameters: ENT input parameters by terminating with ACCEPT F5 or ENT each time RESULT SCREEN Save the result: ENT input point name and point code ACCEPT F5 RETURN TO PARAMETER SCREEN The required calculation parameters and the output are as follows (p27): 26 1 Inverse SP (Start Point) EP (End Point) CO (Known point coordinate) DI (Distance to the unknown point) BE (Direction Angle to the unknown point) Coordinates of three points (P1, P2, P3) Direction Angle (SP->EP) H, V, S Distance Coordinate of the unknown point 2 Point Coordinate 3 Circle Radius Coordinate of centerpoint of the arc, Radius of the arc Coordinates of intersect points (P1, P2) 4 Line-Arc Intersection SP (Start point of the line) EP (End point of the line) CP (Center point of the circle) R (Radius of the circle) S1 (Start point of the 1st line) E1 (End point of the 1st line) S2 (Start point of the 2nd line) E2 (End point of the 2nd line) C1 (Center Point of the 1st circle) R1 (Radius of the 1st circle) C2 (Center Point of the 2nd circle) R2 (Radius of the 2nd circle) SP (Start point of the line) EP (End point of the line) OP (Offset Point) 5 Line-Line Intersection Coordinate of the intersect point 6 Arc-Arc Intersection Coordinates of intersect points (P1, P2) 7 Distance Offset Coordinate of the intersect point of the line and a perpendicular line from the offset point. Distance of the intersect point from the SP of the line Coordinate of the offset point 8 Point Distance Offset SP (Start point of the line) EP (End point of the line) DI (Distance on the line from SP) OD (Offset distance from the line) SP (Start Point of the arc) EP (End point of the arc) R (Radius of the arc) DI (Distance on the arc from SP) OD (Offset distance from the arc) 9 ARC Distance Offset Coordinate of the offset point 27 11. Area Calculation To start area calculation: POWER TOPO LITE MAIN MENU PAGE F5 CALC F2 F4 ENT select points of the polygon by repeating select ( ACCEPT F1 RESULT SCREEN F3 or F4 ) and ENT To return to the calculation menu screen: ESC RESULT SCREEN x2 CALCULATION MENU SCREEN NOTE: This function calculates the length of 2D and 3D contour of a polygon, and the 2D surface (area) of the polygon. The polygon is defined by selecting points in such a way that the contour segments of the polygon do not intersect. The last selected point is automatically tied to the first selected point to form the closed figure. [. . . ] F5 RESULT SCREEN DISTANCE FROM THE PREVIOUS TARGET POINT To change the reference to the present point: RESULT SCREEN DISTANCE FROM THE PREVIOUS TARGET POINT ENT x2 (repeat reference point measurement) To return to PowerTopoLite Main menu: ENT RESULT SCREEN POWER TOPO LITE MAIN MENU 15. VPM (Virtual Plane Measurement) To start VPM: POWER TOPO LITE MAIN MENU PAGE F5 VPM F3 STATION POINT SETUP Station point setup: LIST F2 select the point by FIND PN F2 F4 ENT ACCEPT F5 H. ANGLE SETUP 30 H. angle setup: To input a given angle: INPUT F2 input the value by 0 9 DEF . ENT x2 THREE POINTS MEASUREMENT Or to set the angle 0°: 0 SET F1 x2 ENT THREE POINTS MEASUREMENT Or to calculate by the Back Sight Point: BSP F5 ENT Input value or select from the List THREE POINTS MEASUREMENT LIST F2 SAVE F1 or ACCEPT F5 Measure three points to define the plane: MEAS F1 if necessary, SAVE F2 ENT (repeat measurements of remaining two points) VPM SCREEN Virtual plane measurement: aim a point on the plane if necessary, SAVE F2 To return to PowerTopoLite Main menu: ESC VPM SCREEN POWER TOPO LITE MAIN MENU 16. Changing Preference To access Preference menu: POWER TOPO LITE MAIN MENU PAGE F5 x2 PREF F4 select an item by or ENT F4 F5 F3 ACCEPT or F4 ENT select an option by F3 POWER TOPO LITE MAIN MENU Preference List (page 32) 31 Item ENGLISH X Y Z BASE DIRECTION RIGHT ANGLE HEIGHT CW 10 KEY SYSTEM (ABC) PROCESS TYPE FIXED PLANE ALL IN ONE INFO. [. . . ]