User manual PENTAX IQZOOM 80E

[. . . ] Please take care, as there are even cases where limitations are placed on taking pictures even for personal enjoyment during demonstrations, industrial enterprise or as items for display. Images taken with the purpose of obtaining copyrights also cannot be used outside the scope of use of the copyright as laid out in the Copyright Act, and care should be taken here also. Regarding trademarks · · · · The SD logo is a trademark. PENTAX is a trademark of PENTAX Corporation. Optio is a trademark of PENTAX Corporation. [. . . ] Use the four-way controller ( Filter mode . ) to select the Digital Press the four-way controller ( ). Use the four-way controller ( want to use. ) to select the filter you Setting the slim filter When you select the slim filter in Digital Filter Mode, the slimness setting screen is displayed. z x Caution Use the four-way controller ( Decreases slimness. ) to set the slimness. Increases slimness. Press the OK button. The camera returns to digital filter mode. · The digital zoom cannot be used when the slim filter is selected. 61 Taking Pictures v zxc Using Preset Function Settings (User Mode) In User mode, you can take pictures using the functions and settings registered in advance in User mode. z Taking Pictures 62 Press the four-way controller ( ) in Capture mode. Use the four-way controller ( select User mode ( ). ) to 5 x c v 10/20/2003 11:19 Registering Functions in User Mode p. 75 , /0 xcvbnm z Taking Stereo Pictures (3D Image Mode) You can take 3D pictures using the LCD monitor and view them by the parallel method or cross method (p. 65). If you print out the 3D pictures and look at them through the 3D image viewer provided, the image will appear in three dimensions. Taking Pictures Select the viewing mode. The default setting is [Parallel]. If you do not need to switch to [Cross], go to Step b. z x c Press the MENU button. Press the four-way controller ( to select [3D Mode]. Mode Digital Zoom Instant Review Fast Fwd Movie 3D Mode Memory Sharpness On 2sec Off Parallel Mode Use the four-way controller ( ) to select [Parallel]. It may be especially difficult if the pictures are very large or very small. Try different sizes until the right effect is achieved. Caution · Never look at the sun through the 3D image viewer. · Do not leave the 3D image viewer where it is exposed to direct sunlight as this may lead to fire. b Example of a 3D picture 67 Taking Pictures x z Continuous Shooting (Continuous Shooting Mode) Pictures are taken continuously while the shutter release button is pressed. z Taking Pictures memo Caution Press the four-way controller ( ) button to display on the LCD monitor. 198 10/20/2003 11:19 x Press the shutter release button. Pictures will be taken continuously while the shutter release button is pressed. Shooting stops when you take a finger off from the shutter release button. Playing Back Images p. 24 · You can continue shooting until the SD Memory Card/ MultiMediaCard is full. · The interval will vary according to the [Recorded Pixels] and [Quality Level] setting. · The flash will not discharge in Continuous Shooting mode. · Continuous shooting is not available for Movie Picture, Panorama Assist and 3D Image modes. 68 x z Using the Self-Timer The picture will be taken 10 seconds after the shutter release button is pressed. z x Press the four-way controller ( ) in Capture mode to display on the LCD monitor. The self-timer is engaged and the self-timer lamp lights. The picture is taken approximately 3 seconds after the self-timer lamp starts to blink. 198 Taking Pictures 10/20/2003 11:19 memo · If you turn the LCD monitor on, the second count will be displayed. · To cancel the self-timer, press the four-way controller or the Menu button while the second count is displayed. [. . . ] · The local warranty policies available from Pentax distributors in some countries can supersede this warranty policy. Therefore, we recommend that you review the warranty card supplied with your product at the time of purchase, or contact the PENTAX distributor in your country for more information and to receive a copy of the warranty policy. Appendix The CE Mark is a Directive conformity mark of the European Community. 133 For customers in USA STATEMENT OF FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. [. . . ]