User manual PENTAX MINI SPORT 35

[. . . ] c. ) Adjusting plate assembly (0-M68), Pulley seat assembly (0-M76) Left handed screw (M72) d. ) Restitution spring. assembly (0-M62), Hinge retainer spring (A5) -- CNM 1. 7 x 2. 5 x 2, W3 15. Governor actuator plate (C252) -- Screw (C253), CNL-E 1. 7 x 2. 5 After removing (C252), install CNL-E 1. 7 x 2. 5 again. Slow governor assembly (C100) at 1/125 shutter speed. Governor restitution plate (E407), (E408), (E409), W3 Slow speed cam assembly (0-E402), Nut (E406) -- 23800K-E406-A Caution: a. ) Remove Nut (E406) grabbing slow speed cam shaft (E401) with plier, without turning (E401). [. . . ] Hook plate (E153) a. ) E154 -- b. ) E155 -- c. ) E153 -- W1 42. Top 2nd gear assembly (0-C9) Top 2nd gear shaft retainer nut (C11) 231K-E111-A or 234K-B83-A · 43. Bounce stopper (E145) a. ) E147 -- b. ) E146 -- c. ) E145 -- W3 -- d. ) E152 44. Shutter curtain light seal (A17) After releasing the shutter, remove (A17) -- CNS 1. 7 x 2. 5 x 2 Curtain stopper (E139) a. ) After releasing curtain tension, remove Worm (E41 x 2) b. ) Worm wheel (E42 x2) -- left handed. c. ) Curtain stopper screw (E143) -- 23800K-E143-A d. ) Curtain stopper retainer screw (E142) e. ) (E140), (E141) f. ) Not removing Curtain stopper (E139), retain it with (E142) Shutter curtains a. ) (C27) & (C28) b. ) Curtain plate assembly (0-A25) c. ) Shutter curtain mechanism 0-C1, 0-E36, 0-E38, etc. Top shaft receptacle (C17) Stopper retainer screw (C18) -- CNS 1. 7 x 1. 8 x 2 Idle gear (C624) -- CNL-F 1. 7 x 1. 8 Bottom shaft receptacle (C202) W73, CNS 1. 7 x 1. 6 x 2, CNS 1. 7 x 2. 5 45. 46. 47. 48. 49. 23800 4 /36 50. Coupler gear assembly (0-C222) Coupler gear retainer screw (C226) -- left handed Rewinding actuator lever assembly (0-C241) a. ) CNL-B 1. 4 x 2. 0 b. ) Spring retainer. (C243) c. ) Rewinding actuator lever spring (C242) d. ) 0-C241 Bottom mec. plate assembly (C200) a. ) Stopper pole (C267) -- CNS 1. 7 x 2. 5 b. ) Coupler guide (C268) c. ) C200 d. ) Sprocket (C236) 51. 52. 23800 5 /36 Assembly procedure 1. Bottom mec. plate assembly (C200) a. ) Sprocket (C236) b. ) Bottom mec. plate assembly (C200) -- positioning with (C202) c. ) C268, C267, CNS 1. 7 x 2. 5 Spool a. ) Install spool (0-C20) and Spacer (C29) b. ) Top shaft receptacle (C17-01) c. ) Bottom shaft receptacle (C202) Vertical clearance of Spool is adjusted with W73 (t=0. 5 or 0. 6mm) d. ) Idle gear (C264) 2. 3. Rewinding actuator lever assembly (0-C241) As shown in Parts list Coupler gear assembly (0-C222) -- (C226) = left handed a. ) Sprocket teeth is positioned as shown in Figure 4. b. ) When installing Coupler gear assembly (0-C222), it should be positioned as shown below, besides sprocket teeth should not be moved. 5. Shutter curtains a. ) Top mec. plate assembly (0-C1) -- C27, C28 Curtain strings should not be off from rollers. b. ). Curtain plate assembly (0-A25) Arrangement of both curtains is opposite from SP type camera. 6. Worm (E42) and Worm wheel (E41) Turn worm wheel two rounds to give the tension to both curtains. Check 2nd curtain position after releasing 1st curtain a. ) Install High speed lever assembly (0-E126) temporarily. Cock the shutter, and release 1st curtain, 2nd curtain should be staying at 5mm distant from picture frame. Shutter cocking tool -- 23800K-E113, E124-A. 7. 23800 6 /36 b. ) When both curtains are wound and hooked with 1st curtain ratchet assembly (0-E135), adjust the clearance at 0. 1mm between high speed. lever and Bottom selector gear assembly (0-E124) with turning Adjusting stud (E122). 8. Curtains overlapping After cocking the shutter, both curtains should be overlapping completely or within ± 0. 1mm deviation. Bounce stopper (E152) E152 -- W3 -- E145 -- E146 9. 10. Governor actuator plate (C252) a) Shutter speed at B b) Cock the shutter c) (C252) -- (C253) x 2 as shown in Figure 33. Shutter curtain light seal (A17)-- CNS 1. 7 x 2. 5 x 2 23800 11 /36 34. Tv indication a) Shutter speed at 1/1000 b) Lower pulley of Pulley seat assembly (0-M76) should be in parallel with camera. c) Adjusting plate assembly (0-M68) -- (M72) = left handed d) Restitution spring assembly (0-M62) -- (A5) -- (M85) * Turn wire 1 turn counter-clockwise around the pulley of (0-M62) * After installing (0-M62), Tv wire should not be loose. ·If it is loose, give tension by moving (0-M68), but too much tension makes it harder to adjust the position of Indication plate (M61). e) (M73) -- (0-M74) -- (M75) * Gear of (0-M62) and (0-M74) should be gearing not too deep, and check the function. Mirror housing complete assembly (B000) a) Battery seat assembly (0-A) -- CNS 1. 7 x 2. 5 x 2 b) (B000) should be installed taking care of coupling two gears (M74) and (0-M53). c) (E407) -- (E408) -- (E409) -- W3 23800 12 /36 36. Terminal contact assembly (0-J611) Soldering lead wires 8 pcs. Shutter speed adjustment a) Curtain speed 37. 12. 2 -- 12. 3ms Same way with SP camera. b) High speed adjustment 1/1000 -- 1/60ms Same way with SP camera c) Slow speed adjustment 1/30 -- l sec 1 Loosen screw 2 Adjust with eccentric screw 3 Fasten screw 4 Apply red lacquer on screw 38. Shutter stroke -- Shutter dial at B a) Install Top cover assembly (A300) and Winding lever assembly (C300) temporarily. b) Depressing shutter button gradually, shutter starts working at 2. 1 ± 0. 2mm from origina1 position. c) Self-timer exposure time adjustment at B. (Around 1000ms) 39. Main SW keep adjustment Main SW stroke -- 0. 6 ± 0. 2mm 40. Tv indication a) Shutter speed at 1/1000 b) Positioning adjustment of Supporter plate assembly (0-M53). 23800 13 /36 1 2 Tv indication dial should be set just center portion of viewing finder. Tv indication (1000) should be set as shown in Figure. 3 4 Three jointing gears (0-M53), (0-M62) and (0-M74) must function well. If they do not, adjust the position of Idle gear supporter plate (M73) with eccentric screw A Each figure of Tv indication must come in the center portion, adjusting eccentric screw B 41. Front board plate assembly (A100). [. . . ] Description Body proper Hinge Hinge collar Hinge retainer plate Hinge retainer spring Back cover guide screw Cassette receptacle Battery seat assembly (A8, A9, A10 x 2) Tripod screw Strap hook assembly (A13-01, A14) Top cover retainer screw Mirror box retainer screw Shutter curtain light seal Light seal Body covering, left Body cuvering, right Cover Curtain plate assembly (A25, M7 1 x2) Sprocket shaft receptacle Light seal A B C Connector seat Connector base plate assembly (A35, A36 x3) Insulation plate Quantity 1 1 2 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 2 1 1 1 23602-A23 Interchangeability 23800 22 /36 Parts No. A38 A41-01 A42 A43-01 A44 A45 A46 A47 A48 A49 A100 A104 A105 A106 0-A108 A110 A111 A112 A113-01 A114 A116-01 A121-01 0-A123 A125-01 0-A127-01 Description Connector retainer screw Base plate screw Spacer Light seal curtain Light seal D Light seal E Light seal F Light seal G Strap hook retainer screw Light seal tape Front board plate assembly (A101 -- A149, 0-J401, 0-J601 x 2) Mount ring Mount spring Mount screw Mount lock button assembly (A108, A107, A109) Collar Lock button spring Lock pin supporter plate Front board retainer screw Front board light seal Front board light seal Base plate Charge lever assembly (A123, A122-01, A124) Charge lever shaft A Charge lever shaft B assembly (A127-01, A145) Quantity 1 1 1 2 2 2 1 1 2 1 1 1 1 6 1 1 1 1 4 1 2 1 1 1 1 Interchangeability 23602-A105 23602-A106 23602-A159 23701-A120 A130-01 A132 A134 0-A135 A139-01 0-A143 Button cover Start button Spring B Diaphragm coupler ring assembly (A135, A136 x 5, A137 x 5, A138, A140) Diaphragm coupler ring spring Supporter plate assembly (A143, A144, A146, A147, A148-01) 1 1 1 1 1 1 23800 23 /36 Parts No. A148-01 A149 A200 Description Restitution spring Front board light seal Quantity 1 1 Interchangeability Back cover assembly 1 (A201, A203, A207, A208 x 2, A209, A210 x4, A211, A212, A213, A214, A215, A216 x 4, A217 x 2, A218 A219, A221, A222-01 x 4, A225, A226, A227) Back cover shaft receptacle Pressure plate assembly (A204, A205, A206 x 2) Light seal A Light seal B Pressure plate cover Top cover assembly (A301 -- A336) Accessory shoe Accessory shoe spring Accessory shoe base assembly (A304, A305) Contact spring A Contact spring B Collar Retainer screw Insulation washer SW pin Indication plate Cover ring A Shutter button seat assembly (A316 , A317) Guide screw A Guide screw B Spring Nut Click plate assembly (A323, A324) Shutter button Shutter button core assembly (A326. A327, A328) Cover ring B 2 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 23602-A317 23602-A318 23602-A320 23701-A307 23602-A327 23701-A220 2 A202 0-A204 A217 A218 A220 A300 A302 A303 0-A304 A306 A307 A308 A309 A310-01 A311 A312 A315 0-A316 A318 A319 A320 A322 0-A323 A325 0-A326 A329 23800 24 /36 Parts No. A330-01 A332-01 A334-01 A335 A336 A400 A403 0-A405 0-A501 0-A502 0-A504-02 0-A508 A514 B000 0-B2 B8 0-B9 0-B11 B13 0-B15 B20 0-B22 828 B35 B36 0-B41-01 Description Window C Mask Pattern retainer Light seal Insulation tape Bottom cover (A401, A406) Bottom winding cap Battery cap assembly (A405, A406) Shutter rod assembly (A501, A505, A507) Release plate assembly (A502, A503, A506, A516) Shutter actuator plate A assembly (A504-02, A515-02, A516, CNL-D 1. 4 x 2. 5) Installing seat assembly (A508, A509, A510, A511, A512, A513, LW13) Shutter rod spring Mirror housing complete assembly (B1 -- B112, 0-J531-01, 0-J532-02) Mirror seat assembly (B2, B3, B4, B5, B6 x 4, B7) Spacer Supporter, right assembly (B9, B10) Supporter left assembly (B 11, B12) Mirror seat restitution spring Mirror actuator lever, bottom assembly (B15, B16, B17, B18 x 2, B19, B46) Washer Quantity 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Interchangeability 23602-0-A403 Diaphragm coupler lever assembly 1 (B22, B21, B23, B24 x 2, B25-01, B26-01, B29, B30, B31-01, B32-01, B33, B34) Diaphragm actuator lever connection spring Hook plate Hook plate spring Actuator lever plate assembly (B41-01, B40-01) 1 1 1 1 23800 25 /36 Parts No. [. . . ]