User manual PHILIPS 16857-31-16

[. . . ] Alternatively, if another type of plug (not fused) is used, the fuse at the distribution board should not be greater than 5 Amp. Warning Any unauthorized modification to this equipment may cause violation of the EMC rules resulting in the revocation of the authorization to operate the equipment. Note: we advise you to use the following types of mains power adapters in combination with the camera: U. K. Philips VCM1162/01R EUR Philips VCM1162/00R 2 English Colour Observation Monitor Table of contents Page Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connection and operation facilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Used as a slave monitor it provides the same camera image and sound as the system monitor. The monitor is fitted with a loop-through connector to which a following slave monitor can be connected. The `Colour Observation Monitor' can also be used as a stand-alone system. In this way you can use the slave monitor as a one camera surveillance system. The monitor provides an input for a Philips system camera. The monitor also has an auxiliary input which can be used for any video and audio baseband signal, such as a VCR (playback only). The following items are included in this kit: 1 Colour Observation Monitor 1 System cable (25m/75ft) 1 User manual FA FA R < > NE 6 R < > NE 6 8 7 AR AR 4 4 4 5 4 4 4 4 1 2 Colour Observation Monitor 3 Colour Observation Monitor _ + auto next view Colour Observation system talk action menu CL 66610005_005a. AI 1 2 3 4 5 6 7 8 System monitor Video recorder (VCR) Slave monitor(s) (max. 3) Accessary boxes (0-2 per cable) Interface box System cameras Non system camera's (CVBS) Mains power adapter Mains supply: The monitor accepts a mains power voltage of 100-240V~, 50/60Hz. When the monitor is used as a stand alone system, it supplies a safe low-voltage (16-32V _) for a camera. Read these instructions, before putting your system in operation. g 3 Connection and operation facilities 9 10 11 Aux. in) Input for a third party camera or VCR (playback only). Mains power switch (power) Switches the slave monitor on/off. Slave input (slave in) This input has to be connected to the output of the system monitor. · The slave monitor reproduces the camera image and sound of the camera input which triggered the alarm. · The blinking message "AL" and the camera input number is displayed at the bottom of the monitor screen. 2 The system monitor is in silent mode and the slave monitor is in power save mode · The system mode indication LED is red blinking. 3 The system monitor is in silent mode and the slave monitor is in power active mode · The slave monitor reproduces the camera image and sound of the camera input which triggered the alarm. · The blinking message "AL" and the camera input number is displayed at the bottom of the monitor screen. Reset alarm The alarm resets whenever a button is pressed on the system monitor (for more information you should consult the manual of the system monitor). cable length 100m 200m in video out I O in 0-50m 300m audio in aux slave aux power power CL 66610005_212. AI 1 Power on The slave monitor switches on. There are two possibilities: · The system monitor is in power save mode. The slave monitor starts in power save mode (system mode indication LED is red). · The system monitor is in active mode. The slave monitor performs the same image and sound as the system monitor (system mode indication LED is green). 2 Power off The monitor switches off (system mode indication LED is off). Power save/active Monitor is used as stand alone system When you use the monitor as a stand-alone system a beep will sound for 3 minutes if: a camera cable-short occurs; the camera power is switched off. [. . . ] When an alarm occurs and the system monitor is in non-silent mode, the slave monitor switches on (system mode indication LED is green). Remark: When the system monitor is switched to power save the slave monitor will also switch to power save. Press P to switch the slave monitor to power active again. · · · g 6 System cable For the interconnections between the system monitor and slave monitor a system cable is supplied. For an optimum picture and sound quality you should always use 4-wire dual twisted-pair cable when extending the connection (max. [. . . ]