User manual PHILIPS 42797-86-16

[. . . ] •• Never look into the laser beam inside this system. •• Keep this system away from direct sunlight, naked •• Make sure that you always have easy access to the flames or heat. power cord, plug or adaptor to disconnect the system from the power. Caution •• To prevent possible hearing damage, do not listen at high volume levels for long periods. The louder the volume, the shorter is the safe listening time. • • • • • • • Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. [. . . ] Place the iPod/iPhone/iPad in the dock. Turn on Press . »» The system switches to the last selected source. Tip •• To select another source, press SOURCE repeatedly or the source selection buttons on the remote control. Note •• Remove the protective case before you dock the iPad 4 or iPad mini. Switch to standby mode Press to switch the system to standby mode. »» The clock (if set) appears on the display panel. 9 EN Listen to the iPod/iPhone/iPad Note •• Make sure that the iPod/iPhone/iPad is loaded correctly. 3 4 Press to close the disc tray. 1 2 Press CD on the remote control to select the disc source. »» [Reading] (reading) blinks for a moment, then CD starts playing automatically. If not, press . Press SOURCE repeatedly or DOCK on the remote control to select iPod/iPhone/ iPad source. • To pause or resume play, press . • To search during play, press and hold / , then release to resume normal play. • To go back to the previous iPhone 5 menu, press MENU. • To scroll through the menu, press / . • To confirm a selection, press OK. Play from a USB storage device Note •• Make sure that the USB device contains playable audio content. 1 Insert the USB storage device into the socket. Remove the iPod/iPhone/iPad Pull the iPod/iPhone/iPad out of the dock. Charge the iPod/iPhone/iPad When the system is connected to power, the docked iPod/iPhone/iPad begins to charge. Play disc 1 2 Press to open the disc tray. Insert a disc with the printed side facing up. 2 Press FM/USB repeatedly to select the USB source. »» If no DAB+ station is found, [No DAB Station] (no DAB station) is displayed, then [FULL SCAN] (full scan) is displayed again. To tune to a station from the station list: 1 2 3 4 5 Tune to a DAB+ radio station. Press and hold PROG for 3 seconds to activate the storing mode. Repeat steps 1-4 to store other DAB+ stations. Note •• To remove a pre-stored DAB+ radio station, store another station in its place. Listen to a preset DAB+ radio station In DAB+ mode, press / repeatedly to select a preset channel number. 1 2 In DAB+ mode, press / repeatedly to navigate through the available DAB+ stations. Press OK to confirm the selection. Use DAB+ menu 1 2 In DAB+ mode, press MENU to access DAB+ menu. •• For stations with weak signals: to improve the reception, change to monaural sound. In FM tuner mode, press OK to switch between mono and stereo broadcast. Use FM menu 1 2 In FM mode, press MENU to access FM menu. Press / repeatedly to scroll the menu options: • [SCAN SETTING] (scan setting) • [AUDIO SETTING] (audio setting) • [SYSTEM] (see 'Other features - Use system menu') Press OK to select an option. Repeat steps 2-3 if sub-option is available under one option. Select a preset radio station In tuner mode, press radio station. or to select a preset 3 4 Show RDS information RDS (Radio Data System) is a service that allows FM stations to show additional information. Scan setting • [Strong stations only] (strong stations only): Scan FM stations with strong signals only. • [All stations] (all stations): Scan all the available FM radio stations. Audio setting • [Stereo allowed] (stereo allowed): Select stereo broadcast. [. . . ] No response from the unit •• Disconnect and reconnect the AC power plug, then turn on the unit again. •• As a power-saving feature, the system switches off automatically 15 minutes after track play reaches the end and no control is operated. Remote control does not work •• Before you press any function button, first select the correct source with the remote control instead of the main unit. •• Reduce the distance between the remote control and the unit. [. . . ]