User manual PHILIPS AZ3012

[. . . ] Home service within the normal service area of our Philips Authorised Service Centres will be provided for television receivers with screen size 48cm and above. All other products are to be brought or sent to your nearest Philips Authorised Service Centre. This warranty does not cover: a) Mileage or traveling time, pickup or delivery, cost of insurance. b) Service costs arising from failure to correctly adjust the controls of the product or to observe the instructions, or inspections that reveal that the product is in normal working order. [. . . ] 2 Connect the mains lead to the AC MAINS inlet and the wall socket. The power supply is now connected and ready for use. 3 To switch off completely, unplug the mains lead from the wall socket. · Unplug the mains lead from the wall socket to protect your set during heavy thunderstorms. The typeplate is located on the bottom of the set BASIC FUNCTIONS Switching power on/off: Save energy Whether you are using mains or battery supply, to avoid unnecessary energy consumption always adjust the source selector to off. General operation 1 To select your sound source adjust the source selector to CD/TUNER/OFF. 2 Adjust the sound with the VOLUME and DBB (Dynamic Bass Boost) controls. 3 To switch off the set, adjust the source selector to off position. Note: When the set is switched off the tuner presets will be retained in the set's memory. Tuner Programming radio stations TUNER You can store up to a total of 32 radio stations in the memory: 20 FM and 12 MW(AM). 1 Tune to your desired station (see Radio Reception). 2 Press PROG MODE to activate programming. (See 5) 3 Press PRESET + or ­ once or more to allocate a number from 1 to 20 for FM or 1 to 12 for MW(AM). 4 Press PROG MODE again to confirm the setting. TM Display: prog disappears, the preset number and the frequency of the preset station are shown. (See 3) 5 Repeat steps 1-4 to store other stations. · You can erase a preset station by storing another frequency in its place. Top and front panels (See 1) 1VOLUME ­ adjusts volume level 2DBB (Dynamic Bass Boost) ­ enhances bass response 3Source selector ­ selects source of sound CD or TUNER. Also the power off switch 4Display ­ shows the CD and tuner functions 5FM·MW (AM) ­ selects FM/ MW (AM) waveband 6LIFT TO OPEN ­ opens/ closes the CD door 7PRESS TO PLAY 2; ­ starts or pauses CD play 8STOP 9 ­ stops CD playback; erases a CD programme 9SEARCH , § CD: skips or searches a passage/track backwards or forward Tuner: tunes to a station (up, down) 0PRESET +, ­ ­ selects a preset station (up, down) !PROG MODE CD: ­ programmes and reviews programmed track numbers; ­ plays tracks CD/ programme in random order; ­ repeats a track/CD/ programme Tuner: ­ programmes preset stations Back Panel (See 1) @Telescopic aerial ­ to improve FM reception #Voltage selector (inside battery compartment, some versions only) ­ adjust to match the local voltage 110/220V before plugging in the set $Battery door ­ to open battery compartment %AC MAINS ­ inlet for mains lead Radio reception 1 Adjust the source selector to TUNER. 2 Press FM·MW once or more to select the desired waveband. TM Display: shows your waveband and the preset number and the frequency of a preset station if already programmed (See 3) 3 Press and hold down or § briefly to tune to a radio station. Release when the frequency in the display starts to change. TM The radio automatically tunes to a radio station of sufficient reception. [. . . ] position · To clean the CD, wipe in a straight line from the TM Display: shows no prog briefly when the centre towards the edge using a soft, lint-free programme is cancelled. (See @) cloth. Do not use cleaning agents as they may damage the disc. · Never write on a CD or attach any stickers to it. TROUBLESHOOTING Troubleshooting If a fault occurs, first check the points listed below before taking the set for repair. Do not open the set as there is a risk of electric shock. [. . . ]