User manual PHILIPS CE135BT

[. . . ] Always there to help you Register your product and get support at www. philips. com/welcome Question?Contact Philips CE135BT/10 User manual Manual do utilizador 1 43 Manual del usuario 21 1 Safety 2 Your car audio system 2 11 Reset the system 12 Product information Product Information 16 17 17 18 3 Introduction 3 What's in the box 3 Overview of the system 4 6 7 8 9 10 10 10 10 10 10 10 11 11 11 12 13 13 14 14 15 15 16 13 Troubleshooting 14 Notice 3 Install the car audio system Connect wires Mount into the dashboard Attach the front panel 4 Get started 19 Compliance 19 Care of the environment 19 Trademark notice 19 Copyright 19 For the first time use Set the clock Select a source 5 Listen to radio Select a tuner region Select a tuner sensitivity Enable the RDS function Search for a radio station Store radio stations in memory 6 Play from a storage device 7 Use Bluetooth devices Connect a device Play audio from a Bluetooth device Make a call 8 Listen to an external device 9 Charge your USB device 10 Adjust sound EN 1 English Contents 1 Safety Read and understand all instructions before you use this device. If damage is caused by failure to follow instructions, the warranty does not apply. • Modification of the product could result in hazardous radiation of EMC or other unsafe operation. [. . . ] When you need to change the fuse, consult a professional. •• When you connect other devices to this system, make sure that the rating of the car circuit is higher than the total fuse value of all the connected devices. •• Never connect speaker wires to the metal body or chassis of the car. •• Never connect speaker wires with stripes to one another. 6 EN Note •• Make sure that all loose leads are insulated with •• Consult a professional to connect wires as instructed below. electrical tape. 2 Connect the antenna and amplifier as illustrated, if applicable. e 1 Check the car's wiring carefully and connect them to the the ISO male connectors. L REAR R d ISO male connectors Connect to c b a a b c d e f g h Green strip, blackedged green strip White strip, blackedged white strip Gray strip, blackedged gray strip Purple strip, blackedged purple strip Red strip Blue strip White-edged blue strip Black strip Rear left speaker Front left speaker Front right speaker Rear right speaker Ignition key +12V DC when ON/ ACC Motor/electric antenna relay control lead Amplifier relay control lead Ground 1 2 3 4 5 Sockets on rear panel External sockets or connectors For ISO male connectors REAR L REAR R ANTENNA Purple strip As indicated above Rear left speaker Rear right speaker Antenna OE remote control module Tip •• The pin arrangement for the ISO connectors depends on the type of your vehicle. To avoid damage to the unit, connect properly. EN 7 English Connect wires i Yellow strip To the +12V car battery which is energized at all times Mount into the dashboard • • If the car does not have an on-board drive or navigation computer, disconnect the negative terminal of the car battery. If the car battery is not disconnected, to avoid short-circuit, make sure that the bare wires do not touch each other. Make sure that the car dashboard opening is within these measurements: m 53. 5 mm 18 3m m 1 5m 4 Slide the unit into the dashboard until you hear a "click". 183 mm 53mm 2 Remove the mounting sleeve with the supplied disassembly tools. 5 Attach the trim plate. 3 Install the sleeve into the dashboard and bend the tabs outward to fix the sleeve. 8 EN 6 Reconnect the negative terminal of the car battery. Detach the front panel Note English Attach the front panel 1 Insert the notch on the front panel to the chassis on the main unit. •• Before you insert an SD/SDHC card or reset the •• Before you detach the front panel, make sure that the system is turned off. system, detach the front panel. 1 2 Press to release the front panel. Pull the front panel outwards to remove it. 2 Press the left end of the front panel inwards until it is securely locked with a "click". EN 9 4 Get started For the first time use 1 Press to turn on the system. »» [PHILIPS] is displayed and the device turns to radio mode automatically. 5 Listen to radio Select a tuner region You can select a radio region that matches your location. 1 2 Press and hold menu. to access the system Set the clock 1 2 3 4 Press and hold menu. to access the system Press / repeatedly until [CLK] is displayed with time digits blinking. Rotate Rotate anti-clockwise to set the hour. clockwise to set the minute. Press / repeatedly until one of the following options is displayed. • [AREA EUROPE] (Western Europe) • [AREA ASIA] (Asia Pacific) • [AREA M--EAST] (Middle East) • [AREA AUST] (Australia) • [AREA RUSSIA] (Russia) • [AREA USA] (United States) • [AREA LATIN] (Latin America) Rotate to select a region. 3 Select a source Press AS/SOURCE repeatedly to select a source. • [AUDIO IN]: Listen to the audio input through the AUDIO IN socket. • [USB]: When a USB storage device is connected and recognized, you can select this source to play audio files that are stored on it. • [SD/SDHC]: When an SD/SDHC card is inserted and recognized, you can select this source to play audio files that are stored on it. Select a tuner sensitivity To search for radio stations with strong signals only or more radio stations, you can change the tuner sensitivity. 1 2 3 Press and hold menu. to access the system Press / repeatedly until [LOC ON] or [LOC OFF] is displayed. • [LOC ON]: Search for radio stations with strong signals only. Press repeatedly to select a play mode: • [SHU ALL]: play all tracks randomly, • [SHU FLD]: play tracks in the current folder randomly, or • [SHU OFF]: play all tracks in the storage device in sequence. 1 Connect a compatible USB storage device or SD/SDHC card. • For an SD/SDHC card, detach the front panel first, insert the card into the card slot, and then attach the front panel. Switch the source to [USB] or [SD/ SDHC]. • When a USB storage device is connected and recognized, the system switches the source to [USB] automatically. 2 12 EN 7 Use Bluetooth devices With this car audio system, you can listen to audio from a player or make a call through Bluetooth. Disconnect a device 1 2 3 Press and hold MENU to access the system menu. [. . . ] When you contact Philips, make sure that the product is nearby and the model number and serial number are available. No power or no sound •• The power supply from car battery is cut off, or the car battery runs out of energy. •• Cable is not correctly connected. •• If the above solutions cannot help, press the RESET button. [. . . ]