User manual PHILIPS DCM129

[. . . ] Register your product and get support at www. philips. com/welcome DCM129 EN User manual Contents 1 Important 2 Safety 2 9 Troubleshooting 10 Notice 12 13 2 Your Docking Music System Introduction 4 What's in the box 4 Overview of the main unit 5 Overview of the remote control 5 4 3 Connect Connect speakers Connect power 6 6 6 4 Get started Prepare the remote control Turn on 7 7 8 5 Play Play from iPod/iPhone Play disc Control play 8 8 9 9 6 Listen to radio Tune to a radio station Program radio stations automatically Program radio stations manually Select a preset radio station 10 10 10 10 10 7 Other features Listen to an external device 11 11 8 Product information Specifications 11 11 EN 1 1 Important Safety • • • • Do not install near any heat sources such as radiators, heat registers, stoves, or other device (including amplifiers) that produce heat. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the device. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the device. [. . . ] •• Connect only speakers with impedance that is the the socket completely. d e same or higher than the supplied speakers. Refer to the Specifications section of this manual. f VOL +/• Adjust volume. g PRESET +/• Select a preset radio station. k REPEAT • Play a track or all tracks repeatedly. l SOURCE • Select a source: disc, iPod/iPhone, FM, or AUX. Insert the speaker wires completely into the speaker input sockets on the back of the unit. Connect power Caution •• Risk of product damage!Make sure that the power supply voltage corresponds to the voltage printed on the back or the underside of the Micro Hi-Fi system. •• Before connecting the AC power cord, make sure that you have completed all other connections. 6 EN Connect the AC power cable to the power outlet. 4 Get started Always follow the instructions in this chapter in sequence. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the rear of the apparatus. ___________________________ Prepare the remote control Caution •• Risk of explosion!Keep batteries away from heat, •• Risk of product damage!When the remote control is •• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. not used for long periods, remove the batteries. Never discard batteries in fire. For first-time use: Remove the protective tab to activate the remote control battery. To replace the remote control battery: 1 2 3 1 Open the battery compartment. Insert one CR2025 battery with correct polarity (+/-) as indicated. Close the battery compartment. 2 3 EN 7 Turn on Press POWER. »» The unit switches to the last selected source. 5 Play Play from iPod/iPhone You can enjoy audio from iPod/iPhone through this device. Switch to standby Press POWER again to switch the unit to standby mode. »» The red standby indicator turns on. Compatible iPod/iPhone The unit supports the following iPod/iPhone models. Made for • iPod classic • iPod with video • iPod nano (1st, 2nd, 3rd, 4th, 5th, and 6th generation) • iPod touch (1st, 2nd, 3rd, and 4th generation) • iPhone (4th generation) • iPhone 4 • iPhone 3GS • iPhone 3G • iPhone Load the iPod/iPhone Insert your iPod/iPhone on the dock. 8 EN Charge the iPod/iPhone When the unit is connected to power, the docked iPod/iPhone begins to charge automatically. Control play Display play information During play, press DISPLAY repeatedly to display the play information. Listen to the iPod/iPhone Note •• Make sure that your iPod/iPhone has been loaded securely. Program tracks You can program a maximum of 20 tracks. 1 2 3 4 1 2 Press SOURCE repeatedly to select iPod/ iPhone source. [. . . ] No sound or poor sound •• Adjust the volume. •• Check if the speakers are connected correctly. •• Check if the stripped speaker wires are clamped. Remote control does not work •• Before you press any function button, first select the correct source with the remote control instead of the main unit. [. . . ]