User manual PHILIPS DECT1222S

[. . . ] Table of contents Conformity, environment and safety Declaration of conformity Using GAP standard compliance DECT 122 handset Icons on the handset display DECT 122 base station Installing the DECT 122 Unpacking your DECT 122 Installing the base station Installing and replacing the batteries in the handset Battery life and range Menu structure Handset power OFF and ON Text or number entry Using the telephone Keypad lock / unlock Making a call Call duration counter Redial list Phonebook Call log Intercom Paging Chain Dialing Clock and Alarm Settings Personal settings Handset tones Handset name Auto answer Display language Advanced settings Recall time Dial mode Area code Call barring SOS number Register a handset Unregister PIN code Reset unit Default settings Troubleshooting Table of contents 2 3 4 5 6 6 7 8 8 9 10 10 11 11 11 12 13-14 14-15 16 17 17 17 18 19 19 19 20 20 20 21 22 22 23 23 23 24 25 1 Conformity, environment and safety Safety information This equipment is not designed to make emergency calls when the power fails. An alternative has to be made available to allow emergency calls. Conformity Hereby, Philips declares that the DECT 122 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. This product can only be connected to the analogue telephone networks of the countries mentioned on the packaging. Power requirements This product requires an electrical supply of 220-240 volts, alternating monophased power, excluding IT installations defined in standard EN 60950. In case of power failure, the communication can be lost. The electrical network is classified as hazardous according to criteria in the standard EN 60950. [. . . ] If you have a broadband DSL Internet connection, please make sure you have one DSL filter plugged directly on each line socket used in the house and check the modem and the phone are plugged in the correct filter slot (one specific for each). The electrical network is classified as hazardous according to criteria in the standard EN 60-950. The only way to power down this product is to unplug the power supply from the electrical outlet. Ensure the electrical outlet is located close to the apparatus and is always easily accessible. Please take care that the power supply and telephone line are connected to the correct sockets as incorrect placement could damage your equipment. Always use the line cable provided with the product otherwise you may not have a dialling tone. Connect the power supply Connect the telephone line cord delivered with the product Installing the DECT 122 7 Installing and replacing the batteries in the handset To insert the batteries, open the battery cover, place the batteries as indicated and then replace the battery cover. When the battery icon is blinking, charge is needed. Allow 12 - 15 hours for the batteries to fully charge. On first use it may be necessary to wait for a few minutes before seeing symbols on the display. Never use any battery type other than the one supplied : risk of explosion. Warning : the base station must always be plugged into the mains when charging or when in use. The warranty does not apply to the batteries and any other components which have a limited lifetime or are exposed to wear. Batteries should not be disposed of with general household waste. Battery life and range Optimal battery life is reached after 3 cycles of complete charging & discharging. When reaching the range limit and the conversation becomes crackly, move closer to the base. To reach optimal range, place the base station away from electrical appliances. Battery life in talk time up to 10 hours Battery life in standby mode up to 120 hours Indoor range up to 50 metres Outdoor range up to 300 metres 8 Installing the DECT 122 Menu structure From idle mode, press keys to enter the menu. Use the Navigation to go up or down in the menu list. BACK to exit the menu or to go back to the ADD NUMBER EDIT NUMBER DEL. NUMBER DELETE LIST CLOCK / ALARM DATE/TIME SET ALARM ALARM TONE PERSONAL SET HANDSET TONE OFF/ON ONCE/ON DAILY MELODY 1/2/3 RING VOLUME RING MELODY KEY TONE HANDSET NAME AUTO ANSWER LANGUAGE ADVANCE SET RECALL TIME DIAL MODE AREA CODE CALL BARRING BARR MODE BARR NUMBER SOS NUMBER REGISTRATION UNREGISTER PIN RESET UNIT No. 1/2/3/4 ON/OFF Language list SHORT/LONG TONE/PULSE HIGH/MEDIUM/ LOW/RINGER OFF MELODY 1 - 10 ON/OFF Press Softkey Press Softkey previous menu level. PHONEBOOK Menu structure 9 Handset power OFF and ON To power the handset OFF or ON long press the key. Text or number entry You can enter the names of your phonebook entries character by character, pressing the corresponding key as many times as necessary to reach the desired character. for ENTER NAME Changing a phonebook name or number Press in idle mode PHONEBOOK press Down 2 times You can also create an entry from the redial list and the call log (subscription dependent). Text and number entry see page 10. EDIT NUMBER press Down 1 time scroll to select view the name to confirm. enter new name view number enter new number Viewing the phonebook list Press Down in idle mode Press BACK to return to idle mode. scroll Up/Down in the list To view the details : Press Phonebook 13 Edit a number when browsing phonebook list Press Down in idle mode EDIT NUMBER press Down 1 time ENTER NUMBER enter new name to confirm. enter new number scroll to select Text and number entry see page 10. ENTER NAME Delete an entry when browsing phonebook list Press Down in idle mode DELETE?DELETE NUM press Down 2 times to confirm. scroll to select Delete whole phonebook list when browsing phonebook list Press Down in idle mode DELETE?DELETE LIST press Down 3 times to confirm. Delete a phonebook entry when in idle mode Press in idle mode PHONEBOOK press Down 2 times press Down 2 times DELETE? DELETE NUM view the list scroll to select to confirm. Delete whole phonebook list when in idle mode Press in idle mode PHONEBOOK press Down 2 times DELETE?Phonebook to confirm. DELETE LIST press Down 3 times 14 Call log This feature is available if you have registered to the caller identification service with your operator. The call log stores the last 20 external calls received : - network message service information* * Subject to a subscription with your operator. Accessing / exiting the call log Press Up scroll view the details to exit BACK Consulting the call log The screen can either display : ! [. . . ] scroll to select ON or OFF 18 Personal Settings To rename the handset Press PERSONAL SET press Down 2 times HANDSET NAME press Down 1 time to confirm. enter the name The default name is : PHILIPS. You can enter 10 characters for the handset name. To activate / deactivate the auto answer mode Press PERSONAL SET press Down 2 times If ON you take the line by lifting the handset from the charge cradle. AUTO ANSWER press Down 2 times to confirm. scroll to select ON or OFF To change the display language Press PERSONAL SET press Down 2 times LANGUAGE press Down 3 times to confirm. scroll to select your language Personal Settings 19 Advanced Settings To change the recall time Press ADVANCE SET press Down 3 times to confirm. scroll to select SHORT or LONG RECALL TIME This option is useful when using operator services. To change the dial mode By default your phone is pre-configured with the appropriate dial mode for your country and you don't have to change this setting. [. . . ]