User manual PHILIPS DVP620VR

[. . . ] Digital Video Disc Player & Video Cassette Recorder DVP620VR VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VIDEO Plus+ system is manufactured under license from Gemstar Development Corporation. 1 1 General Information The region code for this set is 2. Since it is usual for DVD movies to be released at different times in different regions of the world, all players have region codes and discs can have an optional region code. If you load a disc of a different region code to your player, you will see the region code notice on the screen. The disc will not playback, and should be unloaded. Introduction Thank you for purchasing this Philips DVD/ VCR. This Owner's Manual explains the basic operation of this DVD/ VCR. Environmental Information 2 Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. [. . . ] · If video or colour fades in and out, you may be copying a copy guarded video tape. Programming a recording (with the 'VIDEO Plus+ system') You no longer need to tediously enter the date, programme number, start and end time. All the information needed for programming is contained in the Plus Code programming number. You can find this Plus Code programming number in most TV listing magazines written next to the concerned programme. 1 Press SV/V+. VIDEO Plus+ system PlusCode No. 12345 ­ ­ ­ ­ SET=SV/V+ CORRECT=CLEAR END=EXIT VIDEO Plus+ system ONCE DAILY WEEKLY SELECT K L CHOOSE B END=EXIT Error message: 'FULL' · If this error message appears after pressing , then all TIMER blocks are already programmed. If you want to clear a programmed recording (TIMER block), select the programme number on TIMER LIST menu and press . 2 Enter the entire Plus Code number. This number is up to 9 digits long and can be found next to the start time of the TV programme in your TV listing magazine. [e. g: 1-234-5 or 1 234 5] If you make a mistake, you can clear your input with CLEAR. 4 Select "ONCE", "DAILY", or "WEEKLY" recording with K/L. Selecting ONCE/ DAILY/ WEEKLY recordings "ONCE": Recording once "DAILY": Repeated daily recordings (Monday to Friday) "WEEKLY": Repeated weekly recordings (every week on the same day) 5 The decoded data appears after confirmation. You can go back to change the data. Select the corresponding input field using B or CLEAR. Change the data with numerical key pads. 12 Programming a Recording (TIMER) "- -" appears at PROG. · The programme number of the TV channel has not yet been assigned to the Plus Code number. Using numerical key pads, select the corresponding programme number (name) of the TV channel. The following message appears on the screen: "ERROR" · The entered Plus Code number is incorrect. Correct your input or end with STATUS/EXIT. · Check the time/date (see chapter 'Installing your video', section 'Setting the time and date'). · A daily recording was entered for the wrong day. Daily programming can only be used for recordings to be made from Monday to Friday. Switching on "VPS/PDC" · Select "VPS/PDC" using g or CLEAR. Press 1 to switch off "VPS/PDC" or press 2 to switch on "VPS/PDC". 6 When all inputs are correct, press STATUS/EXIT. The programming information is stored in a Timer block. [. . . ] Reset the unit by switching the DVD/VCR off, then on again. No sound and picture Picture freezes momentarily during playback Disc can't be played No return to start-up screen when disc is removed The DVD/VCR does not respond to the remote control ­ ­ ­ ­ ­ ­ ­ ­ Buttons do not work or DVD/VCR stops responding DVD/VCR does not respond to some operating commands during playback. DVD/VCR cannot read CDs/DVDs The DVD/VCR switches from DVD mode to VCR mode after 35 minutes The VCR do not record a TV program Aim the remote control directly at the sensor on the front of the DVD/VCR. Replace the batteries in the remote control. Re-insert the batteries with their polarities (+/­ signs) as indicated. [. . . ]