User manual PHILIPS FR960

[. . . ] Digital surround sound receiver FR960 FR970 Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1 Remove fuse cover and fuse. 2 Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. [. . . ] · You can exit the menu at any time by pressing SETUP MENU. 2 Turn X MENU NAVIGATOR until the desired option (or a value) is displayed. 3 Press NEXT 2 to choose the displayed option (or ENTER / OK to confirm a value). · You can leave any option (values remain unchanged) by pressing 1 PREV. Menu structure * EFFECTS Switches sound effects. 3D SURR virtual 3D surround: 0. . . 100 % * VOL BALANCE Adjusts the relative volume balance between the connected speakers. TEST TONE Test tone: on/off VOL FRONT-L Volume front left speaker: ­50. . . +50 VOL FRONT-R Volume front right speaker: ­50. . . +50 VOL CENTER Volume center speaker: ­50. . . +50 VOL REAR-L Volume rear left speaker: ­50. . . +50 VOL REAR-R Volume rear right speaker: ­50. . . +50 VOL SUBWOOFER Volume subwoofer: ­50. . . +50 * SPEAKR SETUP Selects the used speakers. SUBW PRESENT Subwoofer present: yes/no CENTER SPEAKR Center speaker present: yes/no REAR SPEAKER Rear speakers present: yes/no * SPEAKR SIZES Chooses the speaker sizes of the used speakers, for optimal sound reproduction. LARGE indicates a speaker which can reproduce frequencies lower than 50 Hz. If SUBW PRESENT is set to NO, FRONT SIZE can only be set to LARGE. If FRONT SIZE is set to SMALL, CENTER SIZE can only be set to SMALL and consequently a subwoofer must be connected. SUBW PRESENT Subwoofer present: yes/no FRONT SIZE Left and right front speakers: small/large CENTER SIZE Center speaker: small/large REAR SIZE Rear speakers: small/large * SPK DISTANCE Distance between the usual listening position and the speakers. This defines the delay time for the surround sound. DISTANCE L/ R Distance to front speakers: 1. . . 10 m DISTANCE CNTR Distance to center speaker: 1. . . 10 m DISTANCE REAR Distance to rear speakers: 1. . . 10 m * SELECT INPUT Assigns the audio input connectors to the different source selections chosen with SOURCE SELECTOR (see "SOURCE SELECTION" for details). COAX1 Digital coaxial input 1, COAX 1 IN COAX2 Digital coaxial input 2, COAX 2 IN OPT Digital optical input, OPTICAL IN SAT IN Analogue audio input SAT IN VCR IN Analogue audio input VCR IN TV IN Analogue audio input TV IN CDR IN Analogue audio input CDR IN CD IN Analogue audio input CD IN * TUNER Setup for preset radio stations (see "TUNER" for details). AUTO INSTALL Stores radio stations automatically MAN INSTALL Stores radio stations manually GIVE NAME Allows to assign names to stored radio stations RESHUFFLE Resorts stored radio stations 15 MENUS TV menu If the receiver is connected to a Philips CINEMA LINK TV via the CINEMA LINK system control bus sockets (see "CONNECTIONS"), you may use the TV to set up the system. An option called RECEIVER will be added to the TV menu. If CINEMA LINK is on, adjustments on the receiver will be shown on the TV screen for a few seconds. Consult the instruction booklet of your TV on how to use the TV menu. The options offered may vary by TV model. Switching the connection · Press CINEMA LINK to switch the connection between the receiver and the TV either on or off. yIf the connection is switched on, CINEMA LINK ON is displayed. [. . . ] y While news or traffic information is being broadcast the receiver will switch to tuner and NEWS or TA will flash. 4 Press NEWS/TA until the display indication disappears to switch off the function(s). or Press NEWS/TA during an announcement to switch off the function(s). Note: Be sure to switch the news and traffic announcement off during recording, otherwise these announcements also will be recorded. 22 TROUBLESHOOTING English WARNING Under no circumstances should you try to repair the set yourself as this will invalidate the guarantee. [. . . ]