User manual PHILIPS HD 8839

[. . . ] Register your product and get support at www. philips. com/welcome English 02 Type HD8838 SUP 037DRJ OPERATING INSTRUCTIONS 02 EN READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE. IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid. Close supervision is necessary when the appliance is used by or near children. Unplug from outlet when not in use and before cleaning. [. . . ] Place a container under the dispensing spout and push the upper link button to start the cleaning operation. Then, bring the knob back to the central position to allow other brewing programmes. C L E A N I N G O F PERIODIC CLEANING (It is recommended to perform this cleaning every time the milk carafe is removed, when the milk system does not work properly or has milk deposits on it). It is recommended to regularly clean the parts for brewing and frothing milk by dismounting both the parts installed on the machine and those installed on the carafe. Dismount the parts installed on the machine according to the instructions showed in the following figures: T H E M I L K B R E W I N G S Y S T E M · 15 · PERIODIC CLEANING Proceed as follows for the parts installed on the carafe. · Remove the carafe from the machine. · Lift the cover and pay attention that the wand does not splash the remaining milk. · Remove the wand from the cover. · Remove the pin: - Rotate it counter-clockwise. - Take off the pin from the cover. · Wash the cover and the carafe with lukewarm water. · Wash the wand and the pin of the machine by running lukewarm water inside the duct. · After rinsing and drying all components, assemble the pin on the cover: - Place the pin into the cover. Insert the wand in the cover FROM THE STRAIGHT-CUT END and place the cover over the milk container. These parts can also be washed in the dishwasher placing them in the cutlery basket so that they do not get lost. Otherwise, the best way to clean the above-mentioned components is to leave the dismounted parts for 30 min in a basinful of lukewarm water with the specific detergent Saeco Cleaning Powder. (Rinse the parts with running water before reassembling them on the machine). · 16 · Proceed as follows to complete the cleaning process: 1 Remove the top cover paying attention to the suction pipe. 2 Fill the container with lukewarm water: Do not exceed the MAX level indicated on the container. 3 Replace the suction pipe inside the container and close the cover by pressing it to the end. C L E A N I N G O F T H E M I L K B R E W I N G S Y S T E M Place the cup you use every day to enjoy your hot milk. Press the " Green " button until the following page is displayed. Press the " " button to start dispensing water. Dispensing will stop automatically. If you wish to interrupt water dispensing, press the " " button. · 17 · HOT WATER DISPENSING Warning: At the beginning, short spurts of hot water may come out. · Before dispensing hot water, check that the following icon is displayed: Green To reset the machine to normal operation turn the selector switch counterclockwise until it is set to the " " position. When the machine is ready, proceed as follows: · Place a container under the dispensing spout. Orange It may happen that, even though the selector switch has been turned, hot water does not come out and the following icon is displayed. Wait for the warm-up phase to end in order to obtain a flow of hot water from the dispensing spout. · Turn the selector switch clockwise and set it to the " position. Orange If the following icon is displayed, clean the dispensing spout. After placing an empty container press the " " button and wait until the dispensing is finished. Then, hot water may be dispensed. · The following icon will be displayed. Green Press the " " button to start dispensing hot water. · Pour the desired amount of hot water. To stop the hot water dispensing press the " " button. Green · 18 · ADJUSTMENTS The machine that you have bought allows for certain adjustments that will permit you to use it to its full potential. any type of operation inside the coffee bean hopper. Do not pour coffee beans when the coffee grinder is working. The machine allows slight adjustments to the coffee grinder to adapt it to the kind of coffee used. [. . . ] Fill the water tank and prime the circuit (section "Using the Machine for the First Time"). Clean the brew group (section "Brew Group"). Prime the circuit (section "Using the Machine for the First Time"). Rare event that occurs when the machine is auto- Brew a few coffees as described in section "Saeco matically adjusting the dose. [. . . ]