User manual PHILIPS HTS5120

[. . . ] Register your product and get support at www. philips. com/welcome HTS5120 Contents 1 Notice Copyright Compliance Mains fuse (UK only) Trademarks 7 2 2 2 2 2 3 3 4 4 5 5 5 7 7 7 8 9 10 10 10 10 11 12 12 13 13 13 13 14 14 15 15 15 16 Update software Check software version Update software from a CD-R or USB 8 9 Product speciÀcations Troubleshooting 17 18 20 2 Important Safety Product care Disposal of your old product and batteries 10 Index 3 Your home theater Main unit Remote control 4 Connect your home theater Connectors Connect to the TV Connect audio from TV or other devices Connect a Philips Dock for iPod/iPhone 5 Use your home theater Before you start Choose your sound Play a disc Play from a USB storage device More play features Play from radio Play audio from TV or other devices Play from an MP3 player Play from an iPod or iPhone Use Philips EasyLink 6 Change settings Access the setup menu Change general settings Change audio settings Change video settings Change preference settings EN 1 English 16 16 16 1 Notice 2 3 Copyright The replacement fuse must comply with BS 1362 and have the ASTA approval mark. If the fuse is lost, contact your dealer in order to verify the correct type. Note · To conform with the EMC directive This product incorporates copyright protection technology that is protected by method claims of certain U. S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. [. . . ] The files must be stored on the same disc or USB storage device. Press BACK and go to the picture folder. Select a picture, then press OK to start slideshow. Press again to stop music. 1 2 3 4 1 2 3 4 5 Note · Repeat play is only possible within a track/ chapter. Synchronize audio with video If the audio and video are not synchronized, you can delay the audio to match the video. Press and hold AUDIO SYNC until the audio sync message appears on the display panel. Press +/- within five seconds to sync the audio with your video. Play from radio 1 2 1 2 3 / Check that the FM antenna is connected. » "AUTO INSTALL. . . PRESS PLAY' appears on the display panel if you have not installed any radio stations. Press the following buttons to control play: Action Button Quick skip play to a speciÀc time Quick skip to a specific part of a video by entering the time of a scene. Press the Navigation buttons and OK to select: · [TT Time] : Title time. · [Track Time] : Track time. / 1 2 PROGRAM 3 Enter the time of the scene, then press OK. Selects a preset radio station. Press and hold to erase the preset radio station. Manual: Press once to access program mode, press / to assign a number to the radio station, then press again to store the radio station. Automatic: Press and hold for three seconds to reinstall radio stations. 12 EN Note · The home theater can store up to 40 radio stations. 3 · Press to stop the installation. · AM and digital radio are not supported. · If no stereo signal is detected, or if fewer than five stations are found, you are prompted to install the radio stations again. · For the best reception, place the antenna away from the TV or other sources of radiation. To view video: Connect a video cable from the docking station to the TV. · For iPod, check that the TV ON setting on the player is enabled. · For iPhone, select the TV Out options on the player. 4 5 Press DOCK for iPod. » The home theater tests the compatibility of the player. Use the controls on the player to select and play content. Play audio from TV or other devices Press AUDIO SOURCE repeatedly to select the audio output of the connected device (see `Connect audio from TV or other devices' on page 8). Use Philips EasyLink The home theater supports Philips EasyLink, which uses the HDMI CEC (Consumer Electronics Control) protocol. EasyLinkcompliant devices that are connected through HDMI connectors can be controlled by a single remote control. Note · Philips does not guarantee 100% interoperability with all HDMI CEC devices. Play from an MP3 player Connect and play audio files from an MP3 player or other external audio devices. [. . . ] · Ensure that the audio cables are connected and select the correct input source (for example, AUDIO SOURCE, USB) for the device you want to play. Play Disc cannot be played. · Ensure that the home theater supports the disc (see `Product specifications' on page 17 ). · Ensure that the home theater supports the region code of the disc. · For DVD±RW or DVD±R, ensure that the disc is finalized. [. . . ]