User manual PHILIPS LC3131

[. . . ] Philips multimedia projector bSure 1 / bSure 2 English User guide Index 1. Introduction 4-5 Packaging contents 4 Optional accessories 5 Service accessories 5 6-9 Controls 6-7 Remote control 8 Connections 9 10-11 Positioning the projector and screen 10 Switching on the projector 10 Adjusting the focus and size of the image 11 Adjusting the vertical angle of the projector 11 Keystone correction 11 Moving/transporting the projector 11 Preparation 11 Moving/transporting the projector 11 Inserting the batteries in the remote control 11 12-17 General information 12 Computer input 12 Universal Serial Bus (USB) 12 External monitor connection 12 Video input 12 Connecting to a computer 13-14 PC/Macintosh 13 Connection to an external monitor 14 Connecting to video equipment 15-17 CVBS 15 S-VHS 15 Scart connection 15 Component/HDTV (Pr, Y, Pb/ Cr, Y, Cb) 16 Scart connection (RGBS) 17 > 2. Installation Philips Multimedia Projector 2 English User guide bSure1 / bSure 2 Index 5. Operation 18-27 Preparation 18 General 18 Messages 18 General explanation 18 Feedback messages 18 Some examples 18 On Screen Display Menu 19-27 Menu tree 19-20 General explanation 21 Computer adjustments 22-23 Display adjustments 22 Some examples 22 Digital Zoom/Magnification 22 Auto image 22 Horizontal size 22 Shift 23 Picture adjustments 23 Video/S-Video adjustments 24 Display adjustments 24 Picture adjustments 24 General adjustments 25 Audio adjustments 25 General settings 25-27 Loading your own personal start-up screen 26-27 Resetting the projector 27 28-30 Cleaning 28 Cleaning the cabinet 28 Cleaning the lens 28 Cleaning the dust filter 28 Lamp 29 Lamp replacement 29-30 Resetting the lamplife time 30 31-34 < 6. [. . . ] Operation Computer adjustments On Screen Display Menu > For computer signal input, the following `Display' and `Picture' adjustments can be made. Display adjustments · Press Menu and select `Display' in the menu bar. The following `Display' adjustments can now be made according to the instructions under `General explanation': ­ Digital Freeze captures a moving picture (still picture); ­ Digital Zoom enlarges a part of the picture; ­ Magnification adjusts the zoom factor; ­ Auto image automatically sizes and positions the image to fit optimally in the screen picture; ­ Horizontal size adjusts the computer image in a horizontal direction to make the image completely fill the screen; ­ Phase minimises picture imperfections. When connecting the projector to your PC for the first time, be sure to adjust the phase control for optimal readability of the projected text; ­ Shift adjusts the computer image in horizontal and vertical direction to centre it on the screen. Some examples The following `Display' adjustment procedures, follow a slightly different sequence of actions, or may need some further explanation. Digital Zoom/Magnification `Digital Zoom' is used to enlarge a part of the picture. `Display' is highlighted and its sub menu is shown. 2 Use Cursor Control to move the cursor to `Digital Zoom'. 3 Select `On' to switch `Digital Zoom' on. · Press OK to continue, or · Press Menu to exit and continue with the previous Zoom settings. 4 Use the zoom target to select centre of the screen area you wish to enlarge. 5 Use the Magnification slider to adjust the Zoom factor. · Press OK to confirm and exit the menu. 6 Use Cursor Control to select another section of the enlarged area (`Panning'). By pressing the D(igital) Zoom button on the remote control you enter directly into the zoom centre selection screen (step 4). When Digital Zoom is already active, pressing the D(igital) Zoom button will show the Magnification slider; pressing the D(igital) Zoom button twice will turn off Digital Zoom. Auto image The Auto Image function automatically sizes and positions the image to fit optimally in the screen picture. In addition it takes care for phase adjustment. It does not affect the selected picture format. When Auto Image is set to On, the Horizontal size, Shift and Phase options are greyed out. Horizontal size The Horizontal size function is used to size a computer image to make it fit the projected picture. When the OSD menu is active and the horizontal size option is selected, the level will be indicated graphically on a linear scale (slider). AV Mute Source Menu OK Lamp Stand by Temp Tip for Windows users To adjust size and phase correctly 1 Select `Start' and then `Shut down' from the Windows Taskbar. 2 Adjust the projectors size control, so that no vertical bars are visible. [. . . ] · Do not switch the projector off; it will restart the lamp automatically within a few seconds. Picture too dark or bright with external monitor connected ­ · · 'Monitor out' has been enabled, but the external monitor is not correctly connected (the picture on both displays is too bright). Connect the (optional) VGA Y-cable (See `Connecting to an external monitor' under `Installation'). If the VGA Y-cable is correctly connected, verify whether the input impedance of the monitor is correctly set on 75 Ohm. 'Monitor out' has not been enabled, but the external monitor is connected (the picture on both displays is too dark). [. . . ]