User manual PHILIPS MCM398D

[. . . ] Micro Hi-Fi System MCM398D Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1 2 3 Remove fuse cover and fuse. Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. [. . . ] ID-3 The ID-3 tag scrolls (if any). Discs for playback This system is able to play : ­ All pre-recorded audio CDs ­ All finalised audio CDR and audio CDRW discs ­ MP3-CDs (CD-ROMs with MP3 tracks) CD-ROM, CD-I, CDV, VCD, DVD or computer CDs, however, are not possible. Playing a disc 1 2 3 Select CD source. Press OPEN/CLOSE 0 on the front panel to open the CD compartment. Insert a disc with the printed side facing up and press OPEN/CLOSE 0 to close the CD door. "READING" is displayed as the CD player scans the contents of a disc, and then the total number of tracks and playing time (or the total number of albums and tracks for MP3 disc) are shown. Å Selecting a different track Press TUNING S / T (or S/T on the remote control) repeatedly until the desired track number appears in the display. If playback is stopped, pressÉ to start Å playback. 4 To interrupt playback Press É . Å To resume playback, press É again. Å To stop playback Press Ç. 12 CD/MP3/WMA Operations Finding a passage within a track 1 2 Press and hold down on TUNING S / T (or S/T on the remote control). When you recognize the passage you want, release TUNING S / T (or S/T on the remote control). Normal playback continues. Programming the disc tracks Programming tracks is possible when playback is stopped. Up to 20 tracks can be stored in the memory in any order. 1 2 Press PROG on the remote control to enter the programming mode. A track number is shown and PROG flashes. Press TUNING S / T (or S/T on the remote control) repeatedly to select your desired track number. Selecting a desired album/track (MP3/WMA disc only) To select a desired album Press ALBUM/PRESET 4 / 3 (or ALB +/on the remote control) repeatedly. To select a desired track Press TUNING S / T (or S/T on the remote control) repeatedly. For MP3 disc, press ALBUM/PRESET 4 / 3 (or ALB +/- on the remote control) and TUNING S / T (or S/T on the remote control) to select the desired album and track for programming. 3 4 5 Press PROG to confirm the track number to be stored. Repeat steps 2-3 to select and store all desired tracks. To start playback of your disc programme, press Ç followed byÉÅ. Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback. 1 Press REPEAT/SHUFFLE on the remote control to select : SHUF ­ tracks of the entire disc/ programme are played in random order. SHUF REP ALL ­ to repeat the entire disc/ programme continuously in random order. REP ALL ­ to repeat the entire disc/ programme. To return to normal playback, press REPEAT/ SHUFFLE until the various SHUFFLE/REPEAT modes are no longer displayed. If you attempt to programme more than 20 tracks, "FULL" will appear on the display. In this case : The system will exit programming mode automatically. Pressing Ç button will erase all the programmed tracks. Pressing ÉÅ button will start playback of the programmed tracks. 2 Reviewing the programme In stop mode, press and hold PROG until the display shows all your stored track numbers in sequence. You can also press 9 to cancel your play mode. [. . . ] Do not use solvents such as benzene, thinner, commercially available cleaners, or antistatic spray intended for analogue records. Cleaning the disc lens After prolonged use, dirt or dust may accumulate at the disc lens. To ensure good playback quality, clean the disc lens with Philips CD Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with cleaner. Troubleshooting WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. [. . . ]