User manual PHILIPS REM250

[. . . ] The keypad will remain lit for 5 seconds after you release any key. To turn off the keypad back light, press LIGHT once again. (The keypad will not light whenever you press any key. ) 3 CH Keys Use CH+ (or CH-) to select the next higher (or lower) channel for the selected home entertainment component. 11 SCAN Key Press SCAN once to change channels every 3 seconds. Press it again to stop the scan. 12 ENTER Use ENTER once after entering channel numbers on some TV models. 4 SLEEP Key Press SLEEP to activate your TV's internal sleep timer (not available for all TVs) or to program timer. 2. 13 VCR Transport Keys Use the VCR Transport Keys to control your VCR. [. . . ] Immediately press any key except VOL-, LAST, SCAN, or SET. 5. Example ­ Re-assigning The AUD key to be a DVD (Or VCR) key: For example, to have the remote control a TV, a Cable Converter, and two VCRs, you will need to re-assign the unused AUD key to operate the second VCR as follows: 1. Press and hold SET until the red light blinks twice, then release SET. The red light will blink twice. Press VCR once. When re-assignment is done, the red light will blink twice to confirm your choice. The AUD key is now ready to be programmed for your DVD (or VCR) player. See Programming Your Remote Control on page 4. If SCAN is pressed again after any key stops Auto Scan, the remote will continue Auto Scan of the next ID from where it stopped. If you have passed by the code that turns off the TV, press VOL- one or more times until the TV turns on again. To lock in the code and exit Auto Scan, press and release SET the red light will blink twice. To search for codes of other components, repeat steps 2 through 5, but substitute the appropriate key (e. g. , VCR, CBL) for the (VCR or Cable) component you are searching for. ABOUT OTHER FEATURES Volume Lock The remote control is set at the factory to control the volume independently while in the TV, VCR, and CBL modes. g. , TV) while in another mode (e. g. , VCR or CBL), perform the instructions below to lock the volume setting. This procedure will not affect separate control of your audio component's volume in the AUD modes. NOTES: In the search mode, the remote will send IR (infrared) codes from its library to the selected device, starting with the most popular code first. Checking the Auto Scan Codes If you have set up the remote control using Auto Scan, you can now find out which four-digit code is operating your component: 1. On the remote control, press a component key once (e. g. , TV, VCR, CBL or AUD). Press and hold SET until the red light blinks twice, then release SET. The red light will blink twice. NOTE: By pressing AUD before entering the sequence below, the remote control will operate your home theater volume controls in all modes. This feature does not apply to component keys that have been re-assigned. 1. Press and hold SET until the red light blinks twice, then release SET. The red light will blink twice. Scan Key 4. To view the code for the first digit, press 1 once. Wait 3 seconds, count the red light blinks (e. g. , 3 blinks = 3) and write down the number. The SCAN key allows the remote control to scan the TV, VCR and CBL channels. When activated, the remote control will change channels every 3 seconds. [. . . ] To reset to component Sleep function follow steps 1 through 3 above. At the end of step three, the red light will blink four times to indicate the remote is reset to component Sleep function. 1 2 3 4 7 8 TROUBLESHOOTING PROBLEM: Red Indicator Light does not blink when you press a key. SETUP CODES FOR TELEVISION SOLUTION: CÓDIGOS DE PROGRAMACIÓN PARA TELEVISIÓN CODES DE PROGRAMMATION DU TÉLÉVISEUR Replace the batteries with two (2) "AA" alkaline batteries (see Page 3). The VOL+, VOL- and MUTE keys are not functional. Make sure that the volume control is locked to a component that has volume capabilities and is programmed into the remote control. Red Indicator Light blinks when you press a key, but home entertainment component does not respond. Make sure you are aiming the remote control at your home entertainment component and that you are within 15 feet of the component you are trying to control. The remote control does not control home entertainment components or commands are not working properly. Try all listed codes for the component brand being set up. Make sure all components can be operated with an infrared remote control. CH+, CH- and LAST do not work for your RCA TV. Due to an RCA design (19831987), only the original remote control will operate these functions. A-Mark AOC Admiral Adventura Aiko Akai Alaron Ambassador America Action Ampro Anam Anam National Archer Audiovox Baysonic Belcor Bell & Howell Bradford Brockwood Broksonic CXC Candle Carnivale Carver Celebrity Cineral Citizen Clairtone Concerto Contec Craig Crosley Crown Curtis Mathes Changing channels does not work properly. If original remote control required pressing ENTER to change channels, to change channels, press ENTER on the remote after entering a channel number. Tried Auto Scan and still could not find a working code. Try Auto Scan again after clearing out the component key as follows: Press and hold SET until Red Light blinks twice, then release. Then press and release the component key to be cleared twice. Daewoo Daytron Denon Dumont Dwin Electroband Emerson NOTE: To clear all set up codes and restore functions to Default, press SET until red light blinks twice, release SET and enter 9-8-1. [. . . ]