User manual PHILIPS S9171/69 SENSOTOUCH

[. . . ] S91xx/S90xx 1 Plus 1 2 3 1 2 3 1 2 3 4 5 1 2 3 4 2 3 4 1 2 3 4 5 1 2 Basic Plus 3 3 4 3MO 1 2 3 4 5 6 7 8 1M 1 2 3 4 5 6 7 8 9 10 ENGLISH 12 ESPAÑOL 40 FRANÇAIS 69 ITALIANO 98 PORTUGUÊS 127 TÜRKÇE 156 S91XX, S90XX 12 ENGLISH Introduction Congratulations on your purchase and welcome to Philips!To fully benefit from the support that Philips offers, register your product at www. Please read this user manual, as it contains information about the features of this shaver as well as some tips to make shaving easier and more enjoyable. €1) 1 Comb for beard styler attachment 2 Click-on beard styler attachment 3 Click-on trimmer attachment 4 Click-on shaving unit 5 On/off button 6 Socket for small plug 7 Exclamation mark 8 Replacement reminder 9 Battery charge indicator 10 Travel lock symbol 11 Cleaning reminder 12 Replacement symbol 13 SmartClean system 14 Cap of SmartClean system 15 On/off button 16 Cleaning symbol 17 Drying symbol 18 Ready symbol 19 Charge symbol 20 Cleaning cartridge for SmartClean system 21 Adapter 22 Small plug 23 Retaining ring holder 24 Pouch ENGLISH 13 Note:The accessories supplied may vary for different products. [. . . ] The hair length settings on the beard styler attachment correspond to the remaining hair length after cutting and range from 1 to 5mm. 1 Slide the comb straight into the guiding grooves on both sides of the beard styler attachment (‘click’). 2 Press the length selector and then push it to the left or right to select the desired hair length setting. 3 Press the on/off button once to switch on the appliance. 4 You can now start styling your beard. 24 ENGLISH Using the beard styler attachment without comb You can use the beard styler attachment without the comb to contour your beard, moustache, sideburns or neckline. 1 Pull the comb off the beard styler attachment. Note: Grab the comb in the centre to pull it off the beard styler attachment. 2 Press the on/off button once to switch on the appliance. 3 You can now start contouring your beard, moustache, sideburns or neckline. Cleaning and maintenance Note:The accessories supplied may vary for different products. Note: If you remove the adapter from the wall socket during the cleaning program, the program aborts. Note: 30 minutes after the cleaning program and charging have been completed, the SmartClean switches off automatically. Replacing the cartridge of the SmartClean System -- Replace the cleaning cartridge when the replacement symbol flashes orange or when you are no longer satisfied with the result. 1 Press the button on the side of the SmartClean system (1) and lift the top part of the SmartClean system (2). 28 ENGLISH 2 Take the empty cleaning cartridge from the SmartClean system and pour any remaining cleaning fluid out of the cleaning cartridge. You can simply pour the cleaning fluid down the sink. 3 Throw away the empty cleaning cartridge. 4 Unpack the new cleaning cartridge and pull the seal off the cartridge. 5 Place the new cleaning cartridge in the SmartClean system. 6 Push the top part of the SmartClean system back down (‘click’). Cleaning the shaver under the tap Clean the shaver after every shave for optimal shaving performance. [. . . ] Replace the shaving heads (see chapter ‘Replacement’). Disconnect the shaver from the mains for approx. 38 ENGLISH Possible cause Solution Replace (see chapter ‘Replacement’) or clean the shaving heads (see chapter ‘Cleaning and maintenance’). problem An exclamation The shaving heads are soiled or mark , damaged. [. . . ]