User manual PHILIPS SDV8622T

[. . . ] Nonakedflamesources, suchaslighted candles, should be placed on the product. · · · · Notice for USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] The correct disposal of your old product helps prevent potentially negative consequences on the environment and human health. EN 5 English Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. The packaging of this product is intended to be recycled. Contact your local authorities for information about how to recycle the packaging. What's in your box 1 2 3 4 1x 5 6 1x 7 1x 8 1x 2x 9 10 2x 11 12 4x 13 4x 1x 14 1x 4x 1x 1x a SDV8622T/27 antenna b Power supply 100-240V AC / 6V DC 500mA c Wall/Mast bracket d Nut e U-Bolts f Mast clamps g Nuts with lock washers 6 EN h 25mm wood screws i 6m coax cable with connectors j Weather boot k Power injector l Plastic anchors m Washer n 40mm Hexagon screw Installation Installation information This antenna uses a power inserter module to powertheantennaamplifier. It is essential for proper operation of this antenna system that the power inserter be connected between the antenna and any devices such as splitters, matching transformers, networks, etc. Note · Indoor, choose a location near a window which gives the antenna a clear view of the transmitter. Note · Place the antenna away from metal surface to avoid interference. a For indoor wall mount installation Note · Complete all assembly work on the ground b c d before installing on a wall or an antenna mast. 1 Use the nut , washer , and hexagon screw to attach the antenna to the wall/mast bracket. a b c d Antennawithbuilt-inamplifier Power inserter module Splitters or matching transformers (not included) TV or video device 2 Use the screw holes of the wall/mast bracket as a guide to mark position for the wood screws. EN 7 English 3 Get started Determine the signal strength Before Installation, determine the best location for optimum reception. It is important for the antenna to have an unobstructed path to the transmitter. For best results, ensure the antenna faces the location of the transmitter. For outdoor mast mount installation Note · Complete all assembly work on the ground. Raise the completed antenna after assembly. 1 Use the nut , washer , and hexagon screw to attach the antenna to the wall/mast bracket. 3 For wood wall Usethewoodscrewstofixtheantenna tothewoodwallfirmly. 3. 2mm (1/8") 27±5mm 1. 1"±0. 2" 2 Insert U-bolts into the holes of the wall/mast bracket . Slide the mast clamps onto the U-bolts . Attach the four nuts with lock washers to the U-bolts . For concrete wall Drill four holes on concrete wall, put four plastic anchors into the holes. Use wood screwstofixtheantennatotheconcrete wallfirmly. 7. 9mm (5/16") 35±5mm 1. 4"±0. 2" 8 EN 3 Attachtheassemblytothemastfirmly. Rotate You can make a 90 degree rotation to the antenna or the mounting post. English 4 5 Rotate the mast in its mount to adjust the direction. Attach the coaxial cable to the F connector on the underside of the unit. Position the weather boot over the connection. EN 9 Warning · The power injector and power supply are for indoor use only. Tip · This antenna includes a 19. 7ft roll of 3C-2V coaxial cable. If this is not adequate for your needs, replace the cable with a RG-6 coaxial cable instead of adding an extension. Set up a digital tuner with this antenna Connect to the TV Note · Aspreviouslynoted, theamplifier(Power injector + Power supply) must be placed inline between the antenna and any splitter or additional devices. You can install available channels with the digital TV tuner. This automatic process is part of the setup of the tuner. Ensure the antenna has set up properly before the tuner can receive viewable channels. There are two ways to connect the antenna to the TV: · Connect the antenna to a digital tuner. If the signal strength is good enough, the channels can be memorized in the tuner automatically . Tunetotheanaloguechannelsandfind the best antenna location. [. . . ] The liability of Philips is limited to repair or, at its sole option, replacement of the product. Incidental, special and consequential damages are disclaimed where permitted by law. This warrantygivesyouspecificlegalrights. Youmay also have other rights that vary from state to state. [. . . ]