User manual PHILIPS SWA7528S

[. . . ] Press REC twice to record a tape. PROGRAMMING YOUR REMOTE CONTROL Philips/Magnavox Components The remote control can control up to three different components and is already pre-programmed for use with newer Philips/Magnavox audio/video equipment. Unless you want to change a factory setting, skip the programming instructions and simply start using your new remote control. 5 VOL Keys Use VOL+ (or VOL-) to raise (or lower) the sound volume. 14 TV/VCR Press TV/VCR once to view VCR playback or TV through the VCR. 6 POWER Key Press POWER once to turn on or off the selected home entertainment component. 15 FAV CH Key Use to pre-program up to 10 favorite channels. Programming Other Components To control component brands other than Philips/Magnavox, you'll need to perform the following steps to manually program the remote with codes listed under Manufacturer's Codes on pages 28 through 37. Or as an alternative, you can use the Auto Scan feature, on page 5, to program your component codes. The following chart lists the remote component keys and what type of device each key will control: 7 MUTE Key Press MUTE once to turn sound off or on. 16 LIGHT Key Press LIGHT once to turn on or off the keypad backlight. 8 LAST Key Press LAST once to recall the last channel. SETTING UP YOUR REMOTE CONTROL Before using your new remote control, you will need to obtain and install new batteries, as described below. [. . . ] The red light will blink twice. 6. 3. NOTES: Press each key within 10 seconds of the previous entry. Otherwise, the remote control will exit the programming mode. If you press SET at any time (except during step 3), the remote control will exit the programming mode without saving your entries. You will have to start with step 1 to begin programming again. 4. Press the Component key (e. g. , TV, VCR, etc. ) to be moved once, then press the Component key (e. g. , AUD, etc. ) to be re-assigned once. When reassignment is done, the red light will blink twice to confirm your choice. The re-assigned key is now ready to be programmed for the component. See Programming Your Remote Control on page 4. Programming With Auto Scan If your component does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code using Auto Scan. For example, to search for a code for a TV: 1. Press and hold SET until the red light blinks twice, then release SET. Aim the remote control at the TV and press SCAN. Continue aiming the remote control at the TV (which may take up to 5 minutes) until it turns off. On the remote control, press TV, VCR or CBL once. Scanning will start with the current channel, then proceed to the next channel up, and continue until all channels of your TV, VCR or CBL component are scanned. To stop scanning channels, press SCAN. NOTE: If a code digit is "0" , the red light will not blink. 5. Repeat step 4 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit and 4 for the fourth digit. To find codes of other components, repeat steps 1 through 5, but substitute the appropriate key (e. g. , VCR or CBL) for the component you are checking. As before, write down each four-digit code. 6. 3. Re-Assigning Component Keys The remote can be set up to control any combination of four home entertainment components. By following these instructions, you can re-assign or duplicate a component key onto an unused component key. Favorite Channel Scan The FAV CH Key can be pre-programmed with up to 10 of your favorite channels and scans these only. 1 On the remote control, press a component key once (e. g. , TV, VCR, CBL) . 5 6 2. 3. Press and hold SET until the red light blinks twice, then release SET. The red light will blink twice. QUICK FEATURES SETUP GUIDE This guide is provided here for your convenience as a quick reference for performing remote control sequences. 4. Enter first channel, e. g. , 07. [. . . ] Enter 9-9-0; the Red Light will blink twice. Number of blinks equals value of code digit. Repeat with 2, 3, and 4. Sleep Feature Press SLEEP key to activate your component's internal sleep timer. Reassigned key is now ready for programming. 4. Follow instructions above to Set Timer. [. . . ]