User manual PHILIPS SWW1810

[. . . ] Register your product and get support at www. philips. com/welcome SWW1810 EN User manual 3 1 Important Safety 4 4 6 6 7 7 7 8 9 2 Your Wireless HD AV Connect What is in the box 3 Overview The transmitter The receiver The remote control 4 Connect the transmitter to your HD devices 9 Connect the receiver to the HDTV set 9 Connect the IR blaster and IR sensor extender cables 10 Install remote control batteries 10 Installation 5 Activate your Wireless HD AV Connect and set up the link Turn on the power of your HDTV Activate the wireless link 11 11 12 13 13 14 15 15 15 16 16 16 17 17 17 18 6 Mount your receiver Mount your receiver on the wall Mount your receiver on the back of the HDTV 7 Technical data Supported resolution Product specifications 8 Notice Notice for USA Notice for Canada Recycling Disposal of your old product and batteries One Year Limited Warranty 9 Frequently asked question EN 3 English Contents 1 Important Safety e Do not use this apparatus near water. g Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. h Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. This `bolt of lightning' indicates uninsulated material within your unit may cause an electrical shock. The `exclamation mark' calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. Warning · To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus. i Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Close the battery compartment. 4 10 EN AAA AAA 5 Activate your Wireless HD AV Connect and set up the link Turn on the power of your HDTV HDMI OUT DC 5V IR IN On screen display on HDTV On screen display Mode and status English HDM I Standby mode: it is a powersaving mode . . . . . Start up in progress: It takes 1520 seconds. Searching available channels: It occurs when the link cannot establish over 80 seconds after initialization. HDMI On mode with unrecognized CH1 video format HDMI On mode but without input CH1 from the source device HDMI On mode with recognized video CH1 1080P format 1 2 Go to the source menu under the settings menu of your HDTV. Select the HDMI input to which the receiver is connected. HDM I EN 11 Activate the wireless link Switch on the transmitter and receiver In standby mode, a red power LED displays on the transmitter and receiver. You can then turn on the transmitter and receiver in the following ways: Select the source on the transmitter Press the source buttons on the remote control, transmitter or receiver until you see the available video from your device. Tip · For information on the LED indicator status, see the section on `LED indicator status of the transmitter'. LED indicator status of the transmitter and receiver Power LED Solid red Flashing blue Flashing blue Solid blue Solid blue Solid blue · Press on the transmitter and receiver. Source Mode and status LED Off Standby mode: it is a power-saving mode Flashing Start up in progress: It takes blue 15-20 seconds. Flashing Searching available channels: It occurs when the link cannot establish over 80 seconds after initialization. Flashing On mode but without quickly input from the source device Flashing On mode with slowly unrecognized video format Solid On mode with recognized blue video format · Press on the remote control. » Both the transmitter and receiver are turned on. Note · If the link is not established after 80 seconds, move the transmitter, receiver and HDTV closer to each other. The maximum transmission range is up to 65 feet (19. 7 meters). If more than one set of Philips Wireless HD AV Connect is placed in the same room, make sure that the minimum distance among each one is 6 feet 6 inches (2 meters). If using a computer, make sure the video format is supported before the video is displayed, see the chapter on `Technical data' for information. If using a computer, and the picture on your TV is not full screen, see the chapter on `Frequently asked questions' for information. Establish the link between the transmitter and receiver A flashing blue power LED displays until the signal link between the two units are established. Normally, it takes around 15-20 seconds for the link to establish successfully. · · · 12 EN 6 Mount your receiver You can either mount the receiver on the wall or on the back of the HDTV. 5 Mount your receiver on the wall 1 2 3 4 Select a spot near the HDTV. Make sure that the distance between the two holes is 1 25/32" (45 mm) and the diameter of the hole is 3/16" (5 mm). Punch the supplied two anchors into the two holes on the wall. Put the two screws into the anchors and leave 1/8" (3 mm) to mount the receiver on. EN 13 English Hook the key holes at the back of the receiver on the screws. Mount your receiver on the back of the HDTV 1 2 Remove the white protective film from one of the supplied adhesive tapes. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. [. . . ] The computer screen image is not full screen on my TV. · Make sure that there is power supply for the transmitter and receiver. Right-click on an open space on your desktop. Select Graphics Options > Output to > Digital Television (Now the laptop image will only appear on your TV). [. . . ]