User manual PIONEER AVH-P6450

[. . . ] 3 Pay close attention to all warnings in this manual and follow the instructions carefully. 4 Do not allow other persons to use this system until they have read and understood the operating instructions. 5 Do not install the display where it may (i) obstruct the driver's vision, (ii) impair the performance of any of the vehicle's operating systems or safety features, including air bags, hazard lamp buttons or (iii) impair the driver's ability to safely operate the vehicle. 6 Do not operate this display if doing so in any way will divert your attention from the safe operation of your vehicle. [. . . ] This section provides information on DVD operations with this unit which differs from that described in the DVD player's or multi-DVD player's operation manual. When operating DVD player/multi-DVD player by using the touch panel keys, refer to built-in DVD player operation. -- When using a DVD player or multi-DVD player, you cannot operate the DVD menu by touching the menu item directly. This unit does not have ITS playlist and disc title functions. Switch the remote control selection to suitable setting to operate DVD players. Switch the remote control operation mode to DVD to operate the DVD player by using remote control. (Refer to page 19. ) 1 Source icon Shows which source has been selected. 2 Disc type indicator Shows the type of the currently playing disc. 72 En Section DVD Player 16 When using the joystick on the remote control, switch the remote control operation mode to AVH. (Refer to page 19. ) # You can also select a disc by pressing a/b (TILT/DISC) on the remote control when the remote control operation mode is switched to DVD. 4 To perform fast forward or reverse, keep touching o or p. # You can also perform fast reverse/fast forward by holding the joystick left or right. When using the joystick on the remote control, switch the remote control operation mode to AVH. (Refer to page 19. ) Note If you do not use the touch panel keys within 30 seconds, they will be hidden automatically when playing DVD video or video CD. DVD Player Turning the DVD player on or off !1 Touch SCAN on the function menu to turn scan play on. The first 10 seconds of each track is played. 2 When you find the desired track touch SCAN again. During Video CD or CD playback !TRACK ­ Repeat just the current track During MP3/WMA playback !DISC ­ Repeat the current disc 74 En Section DVD Player 16 Selecting audio output When playing DVD video discs recorded with LPCM audio, or video CD discs, you can switch the audio output. This function is not possible when disc playback has been stopped. % Touch L/R SELECT on the function menu to select the audio output. Touch L/R SELECT repeatedly until the desired audio output appears in the display. !RIGHT ­ right En 75 DVD Player Section 17 Audio Adjustments Introduction to built-in DSP features Important We recommend that you record the settings in the sheet on page 121 after you have completed audio adjustments. !Graphic equalizer (GRAPHIC EQ) can be used for 2-channel mode only. Parametric equalizer (PARAMETRIC EQ) can be used for multi-channel mode only. Note When selecting 2-channel mode, audio does not be output from front center and rear center speakers. DSP modes This unit features two DSP modes: the network mode and the standard mode. [. . . ] 8 dBf (0. 7 µV/75 W, mono, S/N: 30 dB) 50 dB quieting sensitivity . . . . . 10 dBf (0. 9 µV/75 W, mono) Signal-to-noise ratio . . . . . . . . . . . . . . . 75 dB (IEC-A network) Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 3 % (at 65 dBf, 1 kHz, stereo) 0. 1 % (at 65 dBf, 1 kHz, mono) Frequency response . . . . . . . . . . . . . . . [. . . ]