User manual PIONEER CLD-900

[. . . ] Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed. D3-4-2-1-7b*_A1_En If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. [. . . ] For example, a talk radio station may provide a phone number as RT. · Program Service Name (PS) ­ The name of the radio station. · Program Type (PTY) ­ This indicates the kind of program currently being broadcast. · Current tuner frequency (FREQ) Note · If any noise is picked up while displaying the RT scroll, some characters may be displayed incorrectly. · If you see NO TEXT in the RT display, it means no RT data is sent from the broadcast station. The display will automatically switch to the PS data display (if no PS data, NO NAME is displayed). · In the PTY display, NO PTY may be shown. MENU TOOLS VOL iPod USB NETWORK ADAPTER AUTO / DIRECT ENTER TUNER BD DVD ALC / STANDARD iPod CTRL ADV SURR CD STB GAME HOME MENU PTY RETURN BAND MUTE RECEIVER TV PORTABLE SOUND WING PRESET TUNE Searching for RDS programs You can search for a program type listed above. 1 Press TUNER then press BAND to select the FM band. · RDS is only possible in the FM band. 2 Press PTY. SEARCH shows in the display. 3 Press PRESET +/­ (or /) to select the program type you want to hear. 4 Press ENTER to search for the program type. The system starts searching through the station presets for a match, stopping when it was found one. If NO PTY is displayed it means the tuner couldn't find that program type at the time of the search. · RDS searches station presets only. If no stations have been preset, or if the program type could not be found among the station presets NO PTY is displayed. You can also adjust the HEIGHT GAIN effect (see Setting the Audio options on page 24). Cannot be selected when the Pre Out is set to Surr. Back (see The Pre Out Setting on page 30). You can also adjust the CENTER IMAGE effect (see Setting the Audio options on page 24). The audio is heard with your surround settings and you can still use the Midnight, Loudness, Phase Control, Sound Retriever and Tone functions. 05 FSS ADVANCE (Front Stage Surround ADVANCE) Allows you to create natural surround sound effects using just the front speakers and the subwoofer. Use to provide a rich surround sound effect directed to the center of where the front left and right speakers sound projection area converges. Front left speaker Front right speaker Using Stream Direct AUTO / DIRECT Use the Stream Direct modes when you want to hear the truest possible reproduction of a source. All unnecessary signal processing is bypassed. AUTO SURR DIRECT See Auto playback on page 22. Sources are heard according to the settings made in the Manual SP Setup (speaker setting, channel level, speaker distance), as well as with dual mono settings. You will hear sources according to the number of channels in the signal. Phase Control, Acoustic Calibration EQ, Sound Delay, Auto Delay, LFE Attenuate and Center image functions are available. Analog and PCM sources are heard without any digital processing. Note · In modes that give 6. 1 channel sound, the same signal is heard from both surround back speakers. SOUND WING HVT speakers make it possible to enjoy a broader-ranging sound. PURE DIR Using the Advanced surround ADV SURR The Advanced surround feature creates a variety of surround effects. [. . . ] 4 Press ALC/STANDARD to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings. Important · If the Control with HDMI function is set to ON, you may not be able to reset the unit. In this case, reset either by turning OFF the Control with HDMI function, or by putting the unit into standby mode by turning off the power of all the connected devices, and resetting after the HDMI indicator on the front panel turns off. Microphone (for Auto MCACC setup) . . 1 Dry cell batteries (AAA size IEC R03) . [. . . ]