User manual PIONEER CMX-5000 annexe 1

[. . . ] COMPACT DISC PLAYER CMX-5000 Operating Instructions Read before use Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Pressing this button causes the BPM synchro count feature to be turned on or off each time it is pressed. ( Mix time control dial (MIX TIME) (see p. 18) This dial is used to specify the mixing time when using the mix button to perform cross fade mixing. 6 Track number calendar display The number corresponding to the track currently being played is lit. The right-facing arrow is lit for tracks with a track number of 21 or higher. Programmed track numbers are lit, and the light for each number for tracks which have already been played are turned off once the tracks are played. 7 Time display Used to display the elapsed playback time (when the remain indicator is unlit) or the remaining playback time (when the remain indicator is lit) of the current track in minutes (M), seconds (S), and frames (F). Note that the amount of time remaining is displayed by default when the power is first turned on. ) Mix mode selection button (MIX MODE SELECT) and indicator (see p. 18) This button is used to select cut-in, zip, echo or cross fade mixing as the type of mixing to be used when segueing between tracks. 8 BPM display Used to display the number of BPM for the current track. Note that depending on the track there may be times when the BPM counter is unable to count the number of BPM. 9 Looping indicator (LOOP) Lights up when playing back in loop mode. 0 Relooping indicator (RELOOP) Lights up when recording a loop. <DRB1254> 9 Read before use CONNECTIONS Before connecting or disconnecting any cables, be sure to first turn off the power switch and remove the power cord from its socket. Note that the connection provided with your CMX-5000 CD player come with a locking lever designed to prevent the cable from inadvertently becoming loose, and that it is necessary to press down on this lever to release the lock in order to disconnect the cable. 1. Connecting the player to the remote control unit First connect the CD player to the remote control unit. Remote control unit EJECT IN/REALTIME CUE OUT EXIT RELOOP LOOP TIME MODE TEMPO EJECT AUTO MIX PLAY IN/REALTIME CUE OUT EXIT RELOOP LOOP TIME MODE TEMPO 0 OUT ADJUST TRACK SEARCH 0 OUT ADJUST CLEAR AUTO CUE ±6/±10/±16 PLAY MODE SELECT AUTO CUE ±6/±10/±16 MT MASTER TEMPO DISC TRACK PROGRAM TRACK SEARCH PLAYER SELECT MT MASTER TEMPO 4 ¢ 4 ¢ SEARCH TRACK TEMPO A 16 10 6 M S F B BPM/TRACK BPM/TRACK PUSH ENTER SEARCH TRACK TEMPO 1 ¡ REMAIN A. CUE 1 ¡ REMAIN A. CUE BPM NEXT 16 10 6 M S F CUE PLAY/PAUSE 0 1234567 8 9 10 11 12 13 14 15 16 17 18 19 20 BPM BPM SYNC INSTANT CHANGE SHORT TIME CHANGE MIX TIME CUE PLAY/PAUSE 0 1234567 8 9 10 11 12 13 14 15 16 17 18 19 20 BPM LOOP RELOOP LOOP RELOOP SHORT TIME 6 REV FWD MIX MODE SELECT MIN MAX 6 REV FWD Lever to release the lock Player ' A PLAYER MIN A·B AUDIO-OUT SELECT EJECT DISC EJECT PHONES MONITOR 0 0 DISC CMX-5000 DJ TWIN CD PLAYER B PLAYER MAX REMOTE CONTROL B PLAYER DIGITAL OUT A A A·B A·B/ AUTO MIX B PLAYER SELECT POWER CMX-5000 connection cable 2. Connecting the system to a DJ mixer (DJM-300, DJM-500, or DJM-600) (connecting audio output and control jack cables) Using the audio cables provided with your CMX-5000 CD player system, insert the white plugs into the left (L) jacks and the red plugs into the right (R) jacks. Note that it is also possible to use the CMX-5000 control cord to control the CMX-5000 from a mixer to make it possible to use fader startup or back cueing. (This does not apply, however, during auto mixing playback. ) How to connect to a DJM-600 DJ mixer CH - 2 PHONO 1 CD 2 /LINE L L CH - 1 LINE CD 1 /LINE CMX-5000 audio cable R R CH - 2 PLAYER CONTROL CH - 1 CMX-5000 control cord CMX-5000 control cord CMX-5000 audio cable DJM-600 Player L ON REMOTE CONTROL B PLAYER DIGITAL OUT OFF CONTROL R AUDIO OUT B PLAYER L L CONTROL A B DIGITAL OUT B MIX R MIX OUT R AUDIO OUT A PLAYER A A PLAYER DIGITAL OUT L CONTROL R AUDIO OUT B PLAYER L L CONTROL B MIX R MIX OUT R AUDIO OUT A PLAYER A ¶ When connecting to a DJM-300 or DJM-500 mixer, use the CMX-5000 audio cables to connect CD1 to A PLAYER and CD2 to B PLAYER as indicated in the diagram above. 3. Connecting the CMX-5000 to other devices A Connecting the CMX-5000 to other mixers To connect the CMX-5000 to other mixers, connect the CMX-5000 AUDIO OUT jacks to the line input jacks or AUX jacks of the mixer. (Do not connect to PHONO jacks, as doing so would result in the sound being distorted and in being unable to obtain normal playback quality. ) 10 <DRB1254> Read before use (Connections) B Connecting the CMX-5000 to stereo amplifiers (when not using a DJ mixer) Stereo amplifier Connect audio cable to CD or AUX input jacks. (Do not connect to PHONO input jacks. ) INPUT CD L Player L ON OFF CONTROL R AUDIO OUT B PLAYER L R CMX-5000 audio cable L REMOTE CONTROL B PLAYER DIGITAL OUT A B DIGITAL OUT B MIX R MIX OUT MIX R MIX OUT C Connecting the CMX-5000 to devices with digital input jacks CD recorder or other device with digital input amplifier DIGITAL INPUT OPTICAL COAXIAL Digital signal cable A PLAYER DIGITAL OUT Player L ON REMOTE CONTROL B PLAYER DIGITAL OUT OFF CONTROL R AUDIO OUT B PLAYER L L CONTROL R MIX OUT R AUDIO OUT A PLAYER A PLAYER DIGITAL OUT A B DIGITAL OUT B MIX A ON B PLAYER DIGITAL OUT OFF A B DIGITAL OUT ¶ When using the digital output jacks, the digital output switch (DIGITAL OUT) must be set to `ON'. Note that it is impossible to use any of the DJ mixing or playback features (i. e. , CUE, LOOP, RELOOP, TEMPO CONTROL, MASTER TEMPO, increase/reduce speed by the jog dial or AUTO MIX PLAY) when using digital output. Also note that when using digital output pausing results not in a start playback pause but in a silent pause instead. 4. Connecting the power cord When all other cables have been connected, insert the plug of the power cord located on the rear panel of the CD player into a wall power socket or into an amplifier reserve power socket. DISC LOADING/UNLOADING Label surface up ' AP LA YE R DIS C EJ EC T 0 PH ON ES A·B AU DIOOU T SE LE CT A·B A·B/ AU TO MON ITOR EJ EC T DIS MIN MAX 0 C A MIX PL ¶ Each insertion slot can only accommodate one disc at a time. Never attempt to load more than one disc at the same time, or attempt to load a second disc when one disc has already been loaded. ¶ When loading a disc, do not placing any twisting force on the disc, or try to force the disc into the slot. [. . . ] Alternatively, press the EJECT button (0) to eject the disc. Disc is not rotating even though power has been turned on. ÷ Disc rotation is automatically halted when no operation is performed for 80 minutes or longer when in pause mode. ÷ There may be times when the CMX-5000 fails to operate properly as a result of static electricity or some other form of interference from an outside source. If any such problem occurs, turn off the power to the CMX-5000, wait for the currently inserted disc to come to a full stop, and then turn on the power again to see if that fixes the problem in question. ÷ The CMX-5000 cannot be used to replay partially-written CD-R or CD-RW discs. ÷ The CMX-5000 cannot be used to replay non-standard-shaped discs or any discs other than 5 inch/12 cm discs or 3 inch/8 cm discs which have been inserted into an 3 inch/8 cm disc adapter. [. . . ]