User manual PIONEER CT-S820S

[. . . ] Also, rear displays should not be in a location where it is a visible distraction to the driver. In some countries or states the viewing of images on a display inside a vehicle even by persons other than the driver may be illegal. Where such regulations apply, they must be obeyed and this unit's DVD features should not be used. NEVER install the display in a location that enables the driver to watch the DVD or Video CD while driving. When you park your car in a safe place and apply the parking brake, the picture appears on the screen. En 3 Section 02 Before You Start About this unit CAUTION ! [. . . ] 3 Press FUNCTION to select one of the initial settings. Press FUNCTION to select one of the initial settings. CLOCK AJST (clock)--FM STP (FM tuning step)--AM STP (AM tuning step)--WARN (warning tone)--AUX1 (auxiliary input1)-- AUX2 (auxiliary input2)--V. IN (AV input setting)--CAMRA (rear view camera setting)-- R-SP (rear output and subwoofer controller)-- E-SCRL (ever scroll)--TV (TV signal setting)-- D. ATT (digital attenuation)--A. RESET (audio reset) # To cancel initial settings, press BAND. # You can also cancel initial settings by holding down FUNCTION until the unit turns off. # When you select CAMRA in V. IN, you can select CAMRA. # When the multi-channel processor (e. g. , DEQP7650) is connected to this unit, you can operate D. ATT and A. RESET instead of R-SP. Setting the FM tuning step The FM tuning step employed by seek tuning can be switched between 100 kHz, the preset step, and 50 kHz. 1 Press FUNCTION to select FM STP. 2 Press c or d to select the FM tuning step. Press d to select 100 (100 kHz). Note If seek tuning is performed in 50 kHz steps, stations may be tuned in imprecisely. Tune in the stations with manual tuning or use seek tuning again. Setting the AM tuning step The AM tuning step can be switched between 9 kHz, the preset step, and 10 kHz. When using the tuner in North, Central or South America, reset the tuning step from 9 kHz (531 kHz to 1 602 kHz allowable) to 10 kHz (530 kHz to 1 640 kHz allowable). 48 En Section Operating this unit 03 1 Press FUNCTION to select AM STP. Setting the AV input You can connect AV components to the AV input with an RCA cable. Switch the AV input setting according to the connected AV component. 1 Press FUNCTION to select R-SP. You can install a rear view camera onto the AV input and display a rear view camera video. When the gear shift is in REVERSE (R) position, the video automatically switches to a rear view camera video. (For more details, consult your dealer. ) !After you set up the rear view camera setting, move the gear shift in REVERSE (R) and confirm if a rear view camera video can be shown on the display. If the display should be switched to a rear view camera video by error while you are driving forward, change the rear view camera setting. When you select CAMRA in V. IN, you can select CAMRA. 1 Press FUNCTION to select CAMRA. 2 Press a or b to switch the rear output setting. Pressing a or b will switch between R-SP FULL (full-range speaker) and R-SP S/W (subwoofer) and that status will be displayed. # When no subwoofer is connected to the rear output, select R-SP FULL. # When a subwoofer is connected to the rear output, set for subwoofer R-SP S/W. Even if you change this setting, there is no output unless you turn the subwoofer output on (refer to Using subwoofer output on page 41). If you change this setting, subwoofer output in the audio menu return to the factory settings. [. . . ] +11 dB (100 Hz), +11 dB (10 kHz) (volume: ­30 dB) HPF: Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . 50/63/80/100/125 Hz Slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ­12 dB/oct Subwoofer (mono): Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . 50/63/80/100/125 Hz Slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]