User manual PIONEER DJM-707

[. . . ] Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. Operating environment temperature and humidity: +5°C ­ +35°C (+41°F ­ +95°F); less than 85%RH (cooling vents not blocked) Do not install in the following locations ÷ Location exposed to direct sunlight or strong artificial light ÷ VENTILATION: When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 5 cm at rear, and 3 cm at each side). wARNING: Slot and openings in the cabinet are provided for Ventilation and to ensure reliable operation of the product and to protect it from overheating, to prevent fire hazard, the openings should never be blocked and covered with items, such as newspapers, table-cloths, curtains, etc. Also do not put the apparatus on the thick carpet, bed, sofa, or fabric having a thick pile. [. . . ] When set to [ON], the indicator lights and the CH-2 equalizer is enabled. When set to [OFF], the indicator goes out and the equalizer circuit is bypassed. When this button is set to On, fader start and back cue can be performed on the CH-1 CD player. Whether the operation is initiated by operation of the CH-1 fader lever, or by the cross fader lever is determined by the position of the front panel's FADER START selector switch; the selection is indicated by the lighting of the top panel's CH-1 FADER START indicator or C. The lever's setting angle can be changed in 45° increments (changing of the angle should be performed by an authorized Pioneer service technician). When lighted, indicates that the front panel's FADER REVERSE switch has been set so that the CH-1 fader lever operates in the reverse direction (see front panel item 38). The CH-1 fader lever is used to control the level of signals sent to the cross fader. signal level is maximum at scale mark "10 , " and minimum at scale mark "0". When the front panel CH-1 FADER REVERSE switch is set to [ON], the signal level is maximum at scale mark "0, " and minimum at scale mark "10". * The channel fader curve can be adjusted by means of the front panel FADER CURVE dials. Lights when the CH-1 fader start/back cue function is enabled (see also top panel item 21 and front panel item 39). Lights when CH-1 cross-fader start/back cue function is enabled (see also top panel item 21 and front panel item 39). Indicates that the front panel's FADER REVERSE switch has been set so that the cross fader now operates in reverse (left side is CH-2, right side is CH-1) (see also front panel item 38). When the lever is moved to the left side, CH-1 is at maximum output and CH-2 is at minimum. when moved to the right side , CH-2 is at maximum output and CH-1 is at minimum. * The cross fader curve can be adjusted individually for CH-1 and CH-2 by means of the front panel FADER CURVE dials. 30 Operating load adjust screw (FEELING ADJ. ) The hexagonal Allen screw located next to the panel's slider opening can be rotated with a hexagonal Allen driver to adjust the sliding resistance of the cross fader lever. When this button is set to On, fader start and back cue can be performed on the CH-2 CD player. Whether the operation is initiated by operation of the CH-2 fader lever, or by the cross fader lever is determined by the position of the front panel's FADER START selector switch; the selection is indicated by the lighting of the top panel's CH-2 FADER START indicator or C. This lever's setting angle can be changed in 45° increments (changing of the angle should be performed by an authorized Pioneer service technician). When lighted, indicates that the front panel's FADER REVERSE switch has been set so that the CH-2 fader lever operates in the reverse direction (see front panel item 38). [. . . ] FADER OPERATIONS Start playback with cross fader 1 To control a connected CD player, set the front panel FADER START selector switch for the corresponding channel to its [C. When using cross fader lever to start the CH-1 CD player, set the front panel C. 1] position; when using the cross fader lever to start the CH-2 CD player, set the front panel C. 3 Move the cross fader lever to the side opposite from the channel you wish to start. [. . . ]